Welcome!
Log In
Create A New Profile
Home
>
Printing
Advanced
Printing
Printing issues ...
Page 108 of 140
Pages:
106
107
108
109
110
Forum List
New Topic
RSS
Subject
Views
Posts
Last Post
New Printer...Help!!!!
by
createanddesign
528
9
07/12/2014 04:25PM
Last Post
by
createanddesign
Support perimeter in slic3r?
by
gmh39
806
1
07/11/2014 11:07AM
Last Post
by
gmh39
Unknown Printing Issue
by
LogicalThinking
392
5
07/11/2014 03:47AM
Last Post
by
waitaki
stuttering steppers & 3mm filament
by
RepRapper_1987
1,146
24
07/09/2014 04:59PM
Last Post
by
Eugie_A_Deef
shrinking prints
by
oldboatguy
1,712
10
07/09/2014 11:59AM
Last Post
by
chngyian
German Reprap X400-Low nozzle temperature
by
Davis3Dprinting
1,517
8
07/09/2014 09:15AM
Last Post
by
justcurious
Definitive Guide to Solve Sloppy Print (Hair or String Problem)
by
shafri
778
5
07/08/2014 07:21PM
Last Post
by
Opus
Is there a way to keep the heatbed heated after printing?
by
ChubbyPanda
367
3
07/08/2014 06:01PM
Last Post
by
jbernardis
top layer, shell not smooth. Please help
by
ngocquynh85
858
11
07/08/2014 10:40AM
Last Post
by
ngocquynh85
Hot end popping out
by
psi3000
453
3
07/08/2014 06:40AM
Last Post
by
vreihen
pronterface issues
by
soaring eagle
441
4
07/07/2014 09:44PM
Last Post
by
soaring eagle
Printing air and filament stopppage
by
BobHewson
751
5
07/07/2014 07:38PM
Last Post
by
BobHewson
Need some help
by
crustyclown
398
2
07/07/2014 12:38PM
Last Post
by
Ralf
Printing with support/ removing support
by
ttttrigg3r
514
3
07/07/2014 12:34PM
Last Post
by
Ralf
heating problems
by
aboyd
521
8
07/07/2014 09:09AM
Last Post
by
happygoluckyaussie
Calibration Issues
by
banthafodder7400
448
5
07/07/2014 07:12AM
Last Post
by
banthafodder7400
Non round circles, undersized prints
(Pages:
1
2
)
by
ncq
2,220
35
07/06/2014 11:47PM
Last Post
by
manton
trouble with my magma hot end
by
dennisleacock
388
3
07/06/2014 08:01PM
Last Post
by
PulsedMedia
Print height problem
by
Ramclear
794
14
07/06/2014 05:54PM
Last Post
by
Ramclear
surface defects, groove and blob observed, need input
by
trustmiao
1,129
2
07/06/2014 03:09PM
Last Post
by
TheReprapExperience
Prints is ok in one side, terrible in other side,
by
trustmiao
531
4
07/06/2014 03:06PM
Last Post
by
TheReprapExperience
Repeated Banding on Vertical Walls
by
TheReprapExperience
362
1
07/06/2014 03:00PM
Last Post
by
TheReprapExperience
ABS printing- just went wrong after a while
by
rtrahms
331
6
07/06/2014 10:00AM
Last Post
by
rtrahms
Random missed steps in Y axis
by
drmaestro
636
5
07/05/2014 03:09AM
Last Post
by
drmaestro
Printing on wrong part of the heat bed on Mendel90
by
scott-gray90
330
2
07/04/2014 02:38PM
Last Post
by
nophead
Portabee GO extrusion troubles
by
LuketheDUKE902
837
4
07/03/2014 10:58PM
Last Post
by
theprs.custom22
After plugging printer in, the heatbed rises to 55.5 degrees and then falls
by
mattwold42
370
4
07/03/2014 07:57PM
Last Post
by
Ultibots
Setup stalled, y stepper stopped responding
by
dafeesh
360
3
07/03/2014 09:09AM
Last Post
by
dafeesh
Motors only vibrate but will not turn
by
surfacelane
This topic has been moved.
Struggle with PLA
by
MrBaz
1,132
11
07/02/2014 09:17PM
Last Post
by
MrBaz
Page 108 of 140
Pages:
106
107
108
109
110