Welcome! Log In Create A New Profile

Advanced

RAMPS Electronics

Support for the quite nice RAMPS Electronics. See also http://reprap.org/wiki/RAMPS
Subject Views Posts Last Post

A problem with PC power supply

by tsbmthai01
884 4 02/12/2012 03:05PM
Last Post by aplavins

Why the thermistor needs a power transistor?

by oniric
819 3 02/10/2012 01:23AM
Last Post by oniric

Can I try RAMPS on a breadboard?

by oniric
1,276 7 02/09/2012 04:53AM
Last Post by oniric

Extruder missing steeps mid-printing

by pikelo
725 6 02/08/2012 08:44PM
Last Post by aplavins

Ramps 1.4 motors unresponsive

by bronzies
1,241 6 02/08/2012 08:11PM
Last Post by aplavins

Thoughts on wiring before I go to far down the wrong road

by mydogjustice
739 2 02/08/2012 07:45PM
Last Post by aplavins

Safe to replace 1N4004 with SY 320/8?

by anwe79
1,250 3 01/26/2012 03:15AM
Last Post by anwe79

What do you use for Z steps?

by Axim2012
772 3 01/25/2012 01:11AM
Last Post by nophead

Recommended way to connect RAMPS to PC PSU?

by Pointedstick
939 2 01/18/2012 05:56PM
Last Post by Andrew Smith

[SOLVED] RAMPS 1.4 Stops heating

by mostley
956 5 01/16/2012 12:51PM
Last Post by mostley

Hint soldering RAMPS 1.2 Attachments

by scuba
738 2 01/13/2012 06:44PM
Last Post by dissidence

[SOLVED] Printing FAILS!

by pikelo
620 2 01/11/2012 12:50PM
Last Post by pikelo

[solved] RAMPS 1.4 Heater Issues

by d4rwen
1,250 3 01/07/2012 08:48PM
Last Post by d4rwen

Question about RAMPS wiring

by nigel_mck
828 3 01/07/2012 07:47PM
Last Post by nigel_mck

Arduino getting really hot, and the Ramps turn off

by MatheusBrum
983 2 01/04/2012 09:56PM
Last Post by dissidence

Can't Upload Firmware to RAMPS

by vulcanrd
3,260 7 01/03/2012 02:13AM
Last Post by BrazenArtifice

[Solved] heater pinouts not working

by 3D2B
685 1 01/02/2012 06:12AM
Last Post by 3D2B

[Resolved] Ramps 1.4 Not driving steppers

by nubspera
1,143 5 01/01/2012 06:23PM
Last Post by nubspera

prints reseting

by Gulf
816 12 12/31/2011 04:31AM
Last Post by misan

I am having a problem with the Stepper extruder

by paulharrington
569 5 12/25/2011 02:51PM
Last Post by johnnyr

US Parts List for RAMPS Attachments

by Chris Martin
2,758 9 12/22/2011 09:59PM
Last Post by Infallibel

PCB MK1 + power supply not enough power? Attachments

by pikelo
905 6 12/22/2011 12:24AM
Last Post by pikelo

Amp Rating

by thewaterengine
1,379 7 12/21/2011 07:22AM
Last Post by rcs

RAMPS 1.2 no power

by cr3a7ure
765 6 12/18/2011 08:31AM
Last Post by cr3a7ure

[SOLVED] Pololu pulsing issue

by unicoder
2,274 9 12/16/2011 02:06AM
Last Post by evilb

13.3V with RAMPS 1.4 with 1N4004 diode

by mostley
1,003 3 12/15/2011 04:05AM
Last Post by mostley

RAMPS Z only one direction, extruder doesn't heat

by pgnat
819 2 12/13/2011 02:15PM
Last Post by misan

Newbie trying to get Prusa with RAMPS 1.4 working

by miro87043
1,480 11 12/13/2011 01:48AM
Last Post by nophead

Problem with endstops.

by Rico
500 2 12/12/2011 02:21AM
Last Post by pikelo

ramps connects, motors don't move

by ambiguousphoton
681 8 12/11/2011 08:57PM
Last Post by BrazenArtifice