Welcome! Log In Create A New Profile

Advanced

Huxley

http://reprap.org/wiki/Huxley Huxley is like Mendel, only smaller and cuter. 
Subject Views Posts Last Post

Hot end comes on full power as soon as Huxly is plugged in.

by LarsIslander
658 2 05/06/2013 06:25AM
Last Post by LarsIslander

Resistor heating up quickly then blowing out

by Harry
2,879 13 05/06/2013 04:06AM
Last Post by LarsIslander

Extruder skipping steps

by markusking
1,391 5 04/19/2013 01:48AM
Last Post by markusking

Vas, bumps and cracks Attachments

by herisuprapto
665 4 04/16/2013 12:43PM
Last Post by DeuxVis

Power supply failing after short while

by halfvoxel
1,664 10 04/12/2013 01:16AM
Last Post by Inquisitor

2 problems

by markusking
519 3 04/10/2013 11:20AM
Last Post by markusking

Help with calibration Attachments

by vasko
683 6 04/04/2013 09:23AM
Last Post by vasko

Techzone Huxley unusable... is a fraud???   (Pages: 1 2)

by immaginaecrea
5,454 42 03/24/2013 06:29PM
Last Post by travistag

Extruder Fitting

by Lawrence_
532 2 03/22/2013 01:47AM
Last Post by Inquisitor

cheap ptfe tubing

by nikbjo
762 2 02/25/2013 12:45AM
Last Post by savio

heatbed heats up when off

by nicholasreiser
704 7 02/22/2013 11:42AM
Last Post by nicholasreiser

Making a RepRapPro Huxley

by fireemblem20
2,258 6 02/18/2013 07:14AM
Last Post by SallyRepRap

calibration huxley Attachments

by adnanserim
894 3 02/14/2013 03:06AM
Last Post by nophead

Reprappro huxley, setting e steps

by smartdev
731 2 02/10/2013 04:48AM
Last Post by smartdev

reprappro huxley heat bed temperature not setting

by smartdev
885 5 02/09/2013 09:32AM
Last Post by smartdev

Doubt in RepRapPro Huxley Commissioning

by pinto.chirayil
927 2 02/04/2013 11:53AM
Last Post by Mike Whittaker

PID definitions

by nowhere.elysium
1,993 7 01/29/2013 08:00AM
Last Post by knicholes

New Electronics

by Atomhax
729 6 01/28/2013 03:12PM
Last Post by Atomhax

Temperatur starts at 503 Celcius

by fantom
755 8 01/15/2013 02:56AM
Last Post by fantom

Part hunt - IDC for ribbon cable to heated bed

by CJS62
989 6 01/12/2013 12:50PM
Last Post by CJS62

Techzone Huxley redesigned / modified parts.

by DeuxVis
2,401 21 01/11/2013 03:12AM
Last Post by DeuxVis

Smaller parts of Huxly in stl files that could be

by mcbig
535 2 01/10/2013 11:50PM
Last Post by mcbig

First prints with reprap, how to calibrate settings? Attachments

by Marsko
1,656 3 01/08/2013 06:35AM
Last Post by robertspil

My hot end thermistor input probably died...?

by Joghurt
1,148 5 01/07/2013 07:41AM
Last Post by satya

is M110 a source of problems?

by fantom
849 5 12/14/2012 01:26AM
Last Post by fantom

Huxley - Wiring (Step 7: Heated bed signal wires) Attachments

by herisuprapto
1,049 5 12/13/2012 11:10PM
Last Post by herisuprapto

discontinous printing Attachments

by fantom
862 19 11/20/2012 01:53PM
Last Post by fantom

TZ Huxely Basics? How do I tune this thing?

by Jojo
730 7 11/20/2012 05:22AM
Last Post by DeuxVis

voltage input (off grid portable supply)

by suneil
722 1 11/19/2012 02:37PM
Last Post by suneil

Problems with PLA sticking to heated bed

by tristan.kemp
7,408 9 11/15/2012 08:28PM
Last Post by hobbean