Welcome! Log In Create A New Profile

Huxley

http://reprap.org/wiki/Huxley Huxley is like Mendel, only smaller and cuter.

Page 4 of 8 Pages:

1 2 345

Forum List New Topic RSS

	Views	Posts	Last Post
how long is your Bowden Tube ? by DaveS	1,030	2	10/16/2013 07:00PM Last Post by tomf2002
Problem with reprappro Huxley after updating firmware. by Hugis	1,806	8	09/28/2013 07:53AM Last Post by droftarts
Heatbed gets too warm. by animator75	1,455	8	08/30/2013 07:00PM Last Post by GreatestApe
nozzle problem, who can help me ? by sarazhang	1,190	1	08/26/2013 04:19AM Last Post by sarazhang
Programming is not responding by see00966	1,391	1	08/24/2013 09:41AM Last Post by see00966
Repsnapper or Slicer code for Techzone Huxley??? by Jojo	1,516	9	08/16/2013 01:00AM Last Post by Jojo
Huxley and Ramps 1.4 heatbed connections by CR_Rusanen	1,249	1	08/15/2013 03:32PM Last Post by CR_Rusanen
Retraction by George1	998	2	08/14/2013 02:05PM Last Post by Phuzzy Logic
tz huxely thermocoupler replacement ? by Jojo	920	3	08/06/2013 03:40AM Last Post by Jojo
y-End Stop: Position? by George1	1,358	3	07/30/2013 12:16PM Last Post by reprappro
Nozzle size Grrrrrr by Suljo	1,493	4	07/25/2013 06:44PM Last Post by Suljo
Huxley and ABS and ReprapPro?! by Suljo	1,585	3	07/24/2013 07:09PM Last Post by Suljo
"PID Autotune failed! Temperature to high" by Physics_Dude	11,261	4	07/23/2013 09:25PM Last Post by Physics_Dude
pumping out to much goo by jackmanuk	1,386	16	07/16/2013 07:48AM Last Post by reprappro
What to do MOSFET's gate is blown by heimfabrikant	1,468	4	07/05/2013 05:37AM Last Post by Traumflug
Power by slice396	1,009	7	07/03/2013 11:34AM Last Post by slice396
Huxley Heatbed no GND connection. by adilmalik	1,042	2	07/03/2013 10:53AM Last Post by Suljo
Failure to Print; Extruder Problems? by KD0SKH	1,291	5	07/03/2013 02:46AM Last Post by KD0SKH
Y motor slows at some point by Suljo	1,082	1	07/01/2013 11:28AM Last Post by Suljo
Extruder starts but never stops (commissioning huxley) by tomf2002	1,297	5	06/29/2013 06:22PM Last Post by testtest
firmware veranderen(geen controle heatbed) by scimp	1,193	1	06/19/2013 05:59PM Last Post by scimp
Doubt Regarding some error messages by pinto.chirayil	934	2	06/17/2013 05:50AM Last Post by nophead
Movement and Temperature by Suljo	1,447	4	06/13/2013 03:42AM Last Post by squeeks
Igus bushing by slice396	2,042	4	06/09/2013 07:47AM Last Post by Ohmarinus
Extruder jam cleaning suggestions by AnMeX13	1,965	6	06/08/2013 12:30AM Last Post by AnMeX13
Lasercut frog by slice396	1,456	3	06/05/2013 10:49AM Last Post by slice396
Problems after firmware upload - Marlin for Sanguinololu by kebv	2,562	7	06/04/2013 08:14PM Last Post by squeeks
Reprappro Huxley bed temp reading low by CJS62	1,566	7	06/03/2013 04:46PM Last Post by kebv
X axis motor issue by tepmurc	996	2	05/22/2013 05:33PM Last Post by tepmurc
Laser cut parts by fireemblem20	2,329	12	05/18/2013 04:55AM Last Post by wouter

Page 4 of 8 Pages:

1 2 345