Subject		Views	Posts	Last Post
	Snappy v3.0 released. by RevarBat	2,762	18	03/30/2018 08:40AM Last Post by orbitalair
	My custom printer by fromhun	1,224	3	03/28/2018 06:53AM Last Post by fromhun
	Introducing the ramps 10 - "Ramps10" an open source multi-configurable stepper controller shield based on the Ramps 1.4 design.   (Pages: 1 2 3 4 5) by Simba	25,266	122	03/20/2018 07:28PM Last Post by Simba
	Resume after power lose in Marlin by hadi	6,542	5	03/16/2018 05:58AM Last Post by hackaday123
	Analog output proximity sensor by leadinglights	2,860	10	01/26/2018 04:31AM Last Post by VDX
	Unlimited DIR outputs with single DIR line by newbob	2,158	10	01/18/2018 03:35AM Last Post by dc42
	An attempt to investigate extrusion system pressure by deckingman	2,148	6	01/17/2018 11:37AM Last Post by drop effect
	Linear electric motors, and high speed printing in general   (Pages: 1 2) by buggy123	9,409	33	01/12/2018 04:29PM Last Post by janbbeck
	Correcting horizontal banding in gcode with python by justine.haupt	4,744	19	01/08/2018 02:07PM Last Post by justine.haupt
	tevo printer not heating up and after completing bed heats up and afetr few seconds lcd screen starts flickering nozile not heating up by Prakash	2,448	4	01/06/2018 04:42AM Last Post by cheapo
	Slicer timings going wrong!! by saintofinternet	2,059	4	01/05/2018 02:33AM Last Post by Dust
	Recommendations for large format heatbed by obelisk79	5,510	9	01/02/2018 11:49AM Last Post by justine.haupt
	Marlin - BLACKOUT (Power Failure) sensor by P3T3	3,319	1	12/20/2017 03:06AM Last Post by P3T3
	CNC/FDM Combo printer by tjtravis	2,598	2	12/16/2017 03:16AM Last Post by o_lampe
	RAMPSXB: An Expansion Shield for RAMPS by SZiv	8,390	16	11/29/2017 11:28AM Last Post by SZiv
	New printbed for the p3steel by amigob	3,123	16	11/25/2017 11:24AM Last Post by amigob
	I need a couple firmware mods-who wanna get paid to do it? by WatIDo	2,881	4	11/25/2017 08:18AM Last Post by JustAnotherOne
	UltraTronics PRO card Pin by Nico84	3,195	3	11/19/2017 04:13AM Last Post by Nico84
	GCode M117 Display Message Command by xohmz	10,482	2	11/13/2017 03:38AM Last Post by dc42
	Delta 3D printer design under 200 € by boylucky	3,668	16	11/08/2017 07:28AM Last Post by boylucky
	Core XZ kinematics like in 3DP troubles by rarprint	5,074	4	11/07/2017 01:38AM Last Post by rarprint
	marlin extruder problem by rainito	5,496	4	11/05/2017 08:35AM Last Post by rainito
	Self made 3d printers - open source or commercial? Two 3d printers in one case by rarprint	3,811	6	11/05/2017 02:15AM Last Post by rarprint
	About the calibration for DLP 3D Printer by cthsieh	3,195	2	10/31/2017 07:17AM Last Post by VDX
	RADDS lcd cable length by vacalos	3,330	11	10/23/2017 05:42AM Last Post by steveava
	12 heat bed's Marlin integration by rarprint	4,672	5	10/18/2017 10:16AM Last Post by rarprint
	Metal corners for delta printers - alu profiles 30x30mm - EU by boylucky	4,115	7	10/17/2017 03:34PM Last Post by dc42
	Arcus3D-C1 3D printable, open source, tripod kinematics, cable printer by darenschwenke	3,466	2	10/14/2017 08:18PM Last Post by darenschwenke
	PolyPropylene Filament by Celcius1	3,202	8	10/13/2017 06:51AM Last Post by JonathanThompson
	How to calibrate DLP 3D Printer by cthsieh	3,353	6	10/08/2017 01:26PM Last Post by VDX