Welcome! Log In Create A New Profile

Advanced

Developers

If you're reading this, you're a developer. Please join: http://reprap.org/mailman/listinfo/reprap-dev 
Subject Views Posts Last Post

ESP32 Printer Board   (Pages: 1 ... 7 8 9)

by CthulhuLabs
9,059 245 01/18/2018 08:23AM
Last Post by CthulhuLabs

Unlimited DIR outputs with single DIR line Attachments

by newbob
190 10 01/18/2018 12:35AM
Last Post by dc42

An attempt to investigate extrusion system pressure

by deckingman
173 6 01/17/2018 08:37AM
Last Post by drop effect

Linear electric motors, and high speed printing in general   (Pages: 1 2)

by buggy123
2,297 33 01/12/2018 01:29PM
Last Post by janbbeck

Correcting horizontal banding in gcode with python

by justine.haupt
2,003 19 01/08/2018 11:07AM
Last Post by justine.haupt

tevo printer not heating up and after completing bed heats up and afetr few seconds lcd screen starts flickering nozile not heating up

by Prakash
420 4 01/06/2018 01:42AM
Last Post by cheapo

Slicer timings going wrong!!

by saintofinternet
303 4 01/04/2018 11:33PM
Last Post by Dust

Recommendations for large format heatbed

by obelisk79
1,254 9 01/02/2018 08:49AM
Last Post by justine.haupt

Marlin - BLACKOUT (Power Failure) sensor

by P3T3
657 1 12/20/2017 12:06AM
Last Post by P3T3

auto resume when power loss

by swaroop
704 7 12/18/2017 08:17PM
Last Post by swaroop

CNC/FDM Combo printer

by tjtravis
656 2 12/16/2017 12:16AM
Last Post by o_lampe

RAMPSXB: An Expansion Shield for RAMPS

by SZiv
2,587 16 11/29/2017 08:28AM
Last Post by SZiv

New printbed for the p3steel Attachments

by amigob
1,175 16 11/25/2017 08:24AM
Last Post by amigob

I need a couple firmware mods-who wanna get paid to do it?

by WatIDo
1,044 4 11/25/2017 05:18AM
Last Post by JustAnotherOne

RAMPSSB: Closed Loop DC servo drivers for RAMPS

by SZiv
1,142 10 11/19/2017 10:49AM
Last Post by SZiv

UltraTronics PRO card Pin Attachments

by Nico84
1,026 3 11/19/2017 01:13AM
Last Post by Nico84

GCode M117 Display Message Command

by xohmz
1,275 2 11/13/2017 12:38AM
Last Post by dc42

Delta 3D printer design under 200 € Attachments

by boylucky
1,711 16 11/08/2017 04:28AM
Last Post by boylucky

Core XZ kinematics like in 3DP troubles Attachments

by rarprint
1,297 4 11/06/2017 10:38PM
Last Post by rarprint

marlin extruder problem

by rainito
1,265 4 11/05/2017 05:35AM
Last Post by rainito

Self made 3d printers - open source or commercial? Two 3d printers in one case Attachments

by rarprint
1,658 6 11/05/2017 12:15AM
Last Post by rarprint

About the calibration for DLP 3D Printer Attachments

by cthsieh
1,271 2 10/31/2017 04:17AM
Last Post by VDX

Just another 330x330x300 Ultimaker with direct drive dual extrusion

by jerryjs8
3,437 18 10/30/2017 11:14AM
Last Post by jerryjs8

RADDS lcd cable length

by vacalos
1,876 11 10/23/2017 02:42AM
Last Post by steveava

12 heat bed's Marlin integration Attachments

by rarprint
2,198 5 10/18/2017 07:16AM
Last Post by rarprint

Metal corners for delta printers - alu profiles 30x30mm - EU Attachments

by boylucky
1,575 7 10/17/2017 12:34PM
Last Post by dc42

Arcus3D-C1 3D printable, open source, tripod kinematics, cable printer Attachments

by darenschwenke
1,729 2 10/14/2017 05:18PM
Last Post by darenschwenke

PolyPropylene Filament

by Celcius1
2,129 8 10/13/2017 03:51AM
Last Post by JonathanThompson

How to calibrate DLP 3D Printer Attachments

by cthsieh
1,642 6 10/08/2017 10:26AM
Last Post by VDX

induction heater for 3d printer(600 C)

by kelesekrem
1,832 6 10/05/2017 12:44PM
Last Post by MattMoses