Welcome! Log In Create A New Profile

Advanced

Delta Machines

Rostock, Kossel, Simpson, 3DR, and more. See: http://reprap.org/wiki/Category:Delta. Previously named "Delta Robots and Stewart Platform" 
Page 44 of 59    Pages: FirstPrevious4243444546NextLast
Forum List New Topic RSS
Subject Views Posts Last Post

Heated bed for Mini Kossel enlargement - advice needed

by dc42 		1,630 6 03/01/2015 12:29AM
Last Post by AndyCart

Delta arms with traxxas joints

by sungod3k 		3,770 23 02/27/2015 01:39PM
Last Post by shadowphile

Delta Printer bad prints - Part II (ABS) Attachments   (Pages: 1 2)

by Stephanel 		1,349 32 02/26/2015 07:36AM
Last Post by dougal1957

Delta Printer bad prints Attachments   (Pages: 1 2)

by Stephanel 		3,396 56 02/25/2015 06:38PM
Last Post by janpenguin

2 Questions about hall effect sensors and steps per mm

by Ggalisky 		1,345 4 02/25/2015 02:38PM
Last Post by dc42

Marlin homing all axis is at the same time

by dannydefel 		1,722 7 02/23/2015 04:36PM
Last Post by Kurzaa

Best settings for thin members with a delta?

by Rett Mikhal 		2,652 9 02/23/2015 12:43PM
Last Post by Rett Mikhal

Enlarging the rostock mini

by mrboost 		1,561 5 02/23/2015 02:25AM
Last Post by Lenbok

Help with configuring FSR probe points (mini kossel with RUMBA)

by RDM6 		2,705 8 02/22/2015 09:58PM
Last Post by svalsorim

advice on bars lubrification issue Attachments

by paul18 		461 2 02/20/2015 01:43PM
Last Post by jaguarking11

Duet USB Drive

by Neosolon 		399 2 02/20/2015 12:48PM
Last Post by dc42

delta rod length question.

by tanner331 		823 2 02/18/2015 11:17AM
Last Post by jaguarking11

RichRap 3DR Build question

by zitman 		607 4 02/18/2015 07:38AM
Last Post by zitman

3dr - print issues Attachments

by bromon 		462 3 02/17/2015 06:06PM
Last Post by jaguarking11

Help with calibration steps per mm x y z on kossel mini

by lokidude 		3,846 4 02/17/2015 02:14PM
Last Post by lokidude

X or Y movement after homing, towers exceeding endstops

by maddog7 		1,513 8 02/17/2015 01:06PM
Last Post by hercek

Manually Calibrated Bed Printing Tilted

by Kurzaa 		669 3 02/17/2015 11:32AM
Last Post by Kurzaa

parallel effector arms

by sungod3k 		538 3 02/15/2015 10:56AM
Last Post by sungod3k

delta segmentation error for marlin

by hercek 		505 3 02/14/2015 05:05PM
Last Post by dc42

delta calibration problem (with pictures smiling smiley ) Attachments

by szivgy 		647 4 02/13/2015 03:03PM
Last Post by dc42

Mini Kossel, Cherry Pi III or The Griffin?

by Horse Renoir 		1,513 20 02/13/2015 10:56AM
Last Post by Pointy

Duet Board X Axis Motor not turning

by Neosolon 		717 9 02/12/2015 07:08PM
Last Post by dc42

IcePick Delta - "Pick and Place" Delta 3D Printer

by DennyP 		689 3 02/10/2015 01:44AM
Last Post by DennyP

Enclosed Delta?

by vimau 		2,333 8 02/09/2015 09:14PM
Last Post by braddo99

New to this and struggling a bit Attachments

by cazzer 		522 2 02/09/2015 09:08PM
Last Post by iira

Mini Kossel, Cannot get Pronterface to show it's online

by Dark Skunk 		1,224 7 02/08/2015 09:56PM
Last Post by Dark Skunk

Change filament a Z height

by ochiburi 		2,433 3 02/07/2015 10:12AM
Last Post by ochiburi

Kossel Mini Flat but tilted

by boksbox 		595 2 02/07/2015 04:52AM
Last Post by boksbox

IR Bed Level Sensing? Attachments

by AndyCart 		2,385 3 02/04/2015 01:06PM
Last Post by VDX

New Mini-Kossel Setup Help Attachments

by [email protected] 		1,135 8 02/04/2015 03:40AM
Last Post by dc42
Page 44 of 59    Pages: FirstPrevious4243444546NextLast