Welcome! Log In Create A New Profile

Delta Machines

Rostock, Kossel, Simpson, 3DR, and more. See: http://reprap.org/wiki/Category:Delta. Previously named "Delta Robots and Stewart Platform"

Page 43 of 59 Pages:

41 424344 45

Forum List New Topic RSS

	Views	Posts	Last Post
Octoprint by mrorange26	488	1	03/22/2015 07:51AM Last Post by mrorange26
delete by Lerathel	487	1	03/21/2015 02:20PM Last Post by Lerathel
Test print jittery head (Pages: 1 2) by bigfilsing	2,988	58	03/21/2015 08:03AM Last Post by bigfilsing
Crappy heated bed by boksbox	462	1	03/21/2015 02:13AM Last Post by boksbox
Extruder, planetary gear or not ? by Lerathel	1,498	12	03/20/2015 11:34PM Last Post by Lerathel
Endstop problems by B_CAMP	570	13	03/20/2015 11:06AM Last Post by B_CAMP
PanelOne LCD problems by Ace67aod	392	2	03/19/2015 06:51PM Last Post by Ace67aod
Ultibots 250VS Delta / Auto Level Calibration Z height too low by prjoe	771	2	03/19/2015 06:13PM Last Post by AndyCart
Smoothie, Brainwave or arduino mega 2560, (Mini Kossel) by Lerathel	3,945	21	03/18/2015 02:27PM Last Post by Lerathel
3dr randem freeze by ekaggrat	546	6	03/18/2015 12:13AM Last Post by ekaggrat
TriMatical - MiniTec 45x32mm profile, highly rigid, scalable print volume deltaprinter by toomaspruuden	839	2	03/17/2015 09:07AM Last Post by jonnycowboy
Duet electronics firmware for delta printers by dc42	2,011	11	03/17/2015 06:03AM Last Post by dc42
Delta stepper movement problems by triplanedave	476	4	03/17/2015 12:30AM Last Post by triplanedave
If you were to do it again, what printer would you have bought? by Dark Skunk	819	5	03/16/2015 01:19PM Last Post by grat
Can a 3mm hot end do 1.75 filament by Dark Skunk	474	2	03/15/2015 01:21AM Last Post by boksbox
3dr problems by Ggalisky	416	2	03/13/2015 11:06PM Last Post by ekaggrat
Carbon fiber rods wall thickness and strength by sungod3k	1,201	4	03/13/2015 09:26AM Last Post by dougal1957
Mini Kossel, Makergeek, flow problem by Dark Skunk	459	1	03/13/2015 07:55AM Last Post by Dark Skunk
Required tolerances on frame alignment by dougal1957	514	4	03/13/2015 06:07AM Last Post by dougal1957
Which extruder to choose? (Pages: 1 2) by 3DRapidClone	17,500	33	03/13/2015 01:54AM Last Post by jmf
3DR issues. by j.smith1995	785	17	03/12/2015 01:26AM Last Post by bigfilsing
Magnetic ball joints experiences / sources by sungod3k	566	2	03/10/2015 07:35AM Last Post by dougal1957
Rostock dual extruder moving problem by alanacv	571	1	03/06/2015 09:21AM Last Post by alanacv
Rostock bed size problem?! by zelos11	560	3	03/06/2015 08:17AM Last Post by zelos11
Implementation of Auto-Leveling Rostock?? by zelos11	694	1	03/04/2015 07:53AM Last Post by zelos11
Three point effector by janpenguin	957	3	03/03/2015 07:58PM Last Post by etfrench
Is it gcode or hardware ?? by jmf	745	22	03/03/2015 11:14AM Last Post by bigfilsing
Print Head Drops between Towers by Aaagogo	1,714	2	03/03/2015 10:53AM Last Post by dc42
Loose Bowden Tube by boksbox	1,959	5	03/01/2015 11:14PM Last Post by boksbox
TwinTeeth: The PCB mini-factory by Diyouware	777	2	03/01/2015 10:26AM Last Post by DeuxVis

Page 43 of 59 Pages:

41 424344 45

Delta Machines

Test print jittery head (Pages: 1 2)

Which extruder to choose? (Pages: 1 2)