Welcome! Log In Create A New Profile

Advanced

Delta Machines

Rostock, Kossel, Simpson, 3DR, and more. See: http://reprap.org/wiki/Category:Delta. Previously named "Delta Robots and Stewart Platform" 
Page 41 of 59    Pages: FirstPrevious3940414243NextLast
Forum List New Topic RSS
Subject Views Posts Last Post

Skew? What is this phenomenon? Attachments

by Johndoe1911 		543 3 05/02/2015 08:05AM
Last Post by vreihen

What to change in marlin after changing motor drivers

by Guzberi 		457 3 04/30/2015 01:39PM
Last Post by Guzberi

My Delta build based on Cherry Pi (A Larger Slice of) Attachments

by dougal1957 		1,690 29 04/29/2015 04:30PM
Last Post by dougal1957

z probe confusion Attachments

by Ash-ta 		773 3 04/29/2015 10:18AM
Last Post by Ash-ta

PLA for Kossel build?

by Mils24 		1,057 4 04/29/2015 02:50AM
Last Post by dougal1957

Extrusion problem maybe?

by Planma 		390 5 04/28/2015 07:39PM
Last Post by dc42

Delta calibration problem Attachments

by IronG 		607 4 04/28/2015 09:05AM
Last Post by IronG

RAMPS + Arduino set-up plan Question for K800

by J.A.C. 		1,334 4 04/27/2015 09:28AM
Last Post by LarsK

How fast does your delta print with good quality?spinning smiley sticking its tongue out

by AndrewBCN 		521 2 04/27/2015 04:02AM
Last Post by AndrewBCN

Manual tuning Sensor for my K800

by pashiran 		369 1 04/27/2015 12:01AM
Last Post by pashiran

Best Delta To Build In 2015

by dopesoner930 		693 3 04/26/2015 05:57PM
Last Post by vreihen

Hooking up the stepper motors on a Mini Kossel

by Jonwpatte 		738 8 04/26/2015 02:45PM
Last Post by dc42

Strange print shift issue

by M4vrick99 		903 5 04/25/2015 11:37PM
Last Post by jaguarking11

Extrusion Problems

by andychang28 		361 4 04/23/2015 09:02PM
Last Post by andychang28

How to convert a 1515 Kossel to 2020?

by dc42 		858 6 04/23/2015 08:34AM
Last Post by dougal1957

What just happened to my Mini Kossel SW?

by Eddy 		435 4 04/23/2015 05:13AM
Last Post by boksbox

New rostock mini with printable base frame

by bigfilsing 		785 13 04/22/2015 09:53PM
Last Post by bigfilsing

Coiled cords for effector plate connections?

by vreihen 		468 3 04/20/2015 06:55AM
Last Post by vreihen

Extrusion does not work anymore Attachments

by Stephanel 		489 10 04/18/2015 11:15AM
Last Post by Stephanel

FSR / Proximity / Z probe or..........

by Bking1340 		1,060 6 04/17/2015 06:50PM
Last Post by Bking1340

Marlin Autoprobe checklist

by disneytoy 		2,472 7 04/15/2015 09:49AM
Last Post by sungod3k

XY movements are scaled by 4.5?

by sungod3k 		384 3 04/14/2015 06:43AM
Last Post by sungod3k

Z Probe (What one if any)

by mikes3ds 		573 4 04/14/2015 04:51AM
Last Post by bigfilsing

another ball link option

by bigfilsing 		481 1 04/14/2015 04:40AM
Last Post by bigfilsing

Rostock Mini Pro Issues   (Pages: 1 2)

by andychang28 		1,952 41 04/13/2015 04:49PM
Last Post by Kurzaa

Could my kossel's linear rail be bad?

by dudesom 		976 6 04/13/2015 01:15PM
Last Post by bigfilsing

Delta printer purchase advise

by pulse69 		689 5 04/13/2015 01:17AM
Last Post by IMBoring25

Marlin 1.02 delta endstops confusion

by Bking1340 		1,181 2 04/12/2015 05:30AM
Last Post by dougal1957

Direct drive e3d - bowden?

by Bking1340 		664 5 04/12/2015 04:30AM
Last Post by Bking1340

About to buy a delta - would like comments on model before I order

by J.A.C. 		651 20 04/10/2015 04:42AM
Last Post by dc42
Page 41 of 59    Pages: FirstPrevious3940414243NextLast