Welcome! Log In Create A New Profile

Advanced

Delta Machines

Rostock, Kossel, Simpson, 3DR, and more. See: http://reprap.org/wiki/Category:Delta. Previously named "Delta Robots and Stewart Platform" 
Subject Views Posts Last Post

Strange reprap discount LCD panel issue

by VJain
152 1 08/19/2017 07:18AM
Last Post by VJain

Dual extrusion, E-only move causing XYZ motion, bug in Marlin?

by sphereinabox
3,628 5 08/16/2017 01:37PM
Last Post by DapDeveloper

my new project:delta xxxl homemade

by titeuf007
938 17 08/16/2017 03:20AM
Last Post by titeuf007

My dumb PCB effector Attachments

by kasom
364 10 08/09/2017 09:01PM
Last Post by kasom

FLSUN from AliExpres   (Pages: 1 ... 8 9 10)

by LVD
29,627 294 08/09/2017 07:19AM
Last Post by Dot

Kossel Mini First Layer Waves / Ripples Attachments

by StuartMoorhouse
233 5 08/08/2017 07:01AM
Last Post by StuartMoorhouse

Erratic homing behavior on large delta

by MakersMic
185 4 08/07/2017 12:50PM
Last Post by dc42

Skewed print from loose pulley

by firefly555
222 6 08/06/2017 11:28PM
Last Post by DjDemonD

BIQU Kossel Plus kit

by DaveA
428 2 08/06/2017 07:57PM
Last Post by tatubias

Tips to improve small objects print quality?

by Lexar
280 11 08/06/2017 10:57AM
Last Post by Lexar

3d printing woes. First layer good distance. But blobs/strong getting in way? Attachments

by Jmtech
229 3 07/29/2017 11:56PM
Last Post by Jmtech

Jaycar Rostock calibration

by benno802
263 6 07/26/2017 03:26PM
Last Post by FA-MAS

Help! New delta G28 doesnt home. But moves all motors about 10mm opposite way

by Jmtech
180 4 07/25/2017 12:39PM
Last Post by Jmtech

Help! Delta refuse to get closer then 1mm to the bed

by SlowFoot
187 1 07/25/2017 11:25AM
Last Post by SlowFoot

KILLED. PRINTER HALTED solved...

by tonyoses
345 3 07/23/2017 04:54PM
Last Post by tonyoses

Ripple Eliminator

by uvarovkv
1,171 17 07/19/2017 07:36PM
Last Post by fredchan

Direct extrusion and Rostock mini

by ax2013
303 8 07/18/2017 02:01PM
Last Post by ax2013

Sintron Kossel Z height will not lower print head enough

by Wibbles
158 3 07/18/2017 11:33AM
Last Post by Wibbles

Delta (3DR Based) Will Not Move After G28 Attachments

by Syko_Symatic
182 1 07/17/2017 03:34PM
Last Post by Syko_Symatic

Can anyone explain how to use M666 Marlins?

by disneytoy
10,698 24 07/15/2017 10:04AM
Last Post by .AleX.

Delta calibration - backwards!

by crenzi
259 1 07/15/2017 03:32AM
Last Post by crenzi

Question about delta auto calibration and auto bed leveling

by scanboy
303 4 07/13/2017 12:31PM
Last Post by scanboy

Folgertech Kossel Rev A strangesness

by SlowFoot
185 2 07/11/2017 12:04PM
Last Post by Qdeathstar

The Anycubic Delta on AliExpress any good?   (Pages: 1 2)

by siddharta
6,069 34 07/10/2017 06:47AM
Last Post by NTTD

Removing vertical lines on prints Attachments   (Pages: 1 2 3)

by nebbian
4,355 78 07/09/2017 08:14AM
Last Post by SJN

Extruder run differently with same configuration Attachments

by cthsieh
181 4 07/06/2017 05:23PM
Last Post by cthsieh

Which printer to build? Recommendations required

by Inhumierer
235 3 07/05/2017 10:56AM
Last Post by Inhumierer

Delta Calibration firmware for atmega + ramps 1.4

by VJain
859 18 07/02/2017 07:59AM
Last Post by VJain

About configuring the Marlin for Delta machine Attachments

by cthsieh
268 1 06/29/2017 01:15AM
Last Post by cthsieh

Cherry Pi III Is Available Attachments   (Pages: 1 ... 42 43 44)

by AndyCart
59,824 1,303 06/27/2017 05:18PM
Last Post by mkeveney