Welcome! Log In Create A New Profile

Advanced

Delta Machines

Rostock, Kossel, Simpson, 3DR, and more. See: http://reprap.org/wiki/Category:Delta. Previously named "Delta Robots and Stewart Platform" 
Subject Views Posts Last Post

Zonestar D810B from AliExpress   (Pages: 1 2 3 4 5)

by frankvdh
6,467 124 08/05/2017 11:23PM
Last Post by Hergonoway

3d printing woes. First layer good distance. But blobs/strong getting in way? Attachments

by Jmtech
187 3 07/29/2017 11:56PM
Last Post by Jmtech

Jaycar Rostock calibration

by benno802
235 6 07/26/2017 03:26PM
Last Post by FA-MAS

Help! New delta G28 doesnt home. But moves all motors about 10mm opposite way

by Jmtech
157 4 07/25/2017 12:39PM
Last Post by Jmtech

Help! Delta refuse to get closer then 1mm to the bed

by SlowFoot
158 1 07/25/2017 11:25AM
Last Post by SlowFoot

KILLED. PRINTER HALTED solved...

by tonyoses
215 3 07/23/2017 04:54PM
Last Post by tonyoses

Ripple Eliminator

by uvarovkv
1,082 17 07/19/2017 07:36PM
Last Post by fredchan

Direct extrusion and Rostock mini

by ax2013
280 8 07/18/2017 02:01PM
Last Post by ax2013

Sintron Kossel Z height will not lower print head enough

by Wibbles
136 3 07/18/2017 11:33AM
Last Post by Wibbles

Delta (3DR Based) Will Not Move After G28 Attachments

by Syko_Symatic
153 1 07/17/2017 03:34PM
Last Post by Syko_Symatic

Can anyone explain how to use M666 Marlins?

by disneytoy
10,054 24 07/15/2017 10:04AM
Last Post by .AleX.

Delta calibration - backwards!

by crenzi
231 1 07/15/2017 03:32AM
Last Post by crenzi

Question about delta auto calibration and auto bed leveling

by scanboy
226 4 07/13/2017 12:31PM
Last Post by scanboy

Folgertech Kossel Rev A strangesness

by SlowFoot
165 2 07/11/2017 12:04PM
Last Post by Qdeathstar

AnyCubic Kossel Board Replacement

by twwd
1,480 20 07/11/2017 07:33AM
Last Post by Qdeathstar

The Anycubic Delta on AliExpress any good?   (Pages: 1 2)

by siddharta
5,262 34 07/10/2017 06:47AM
Last Post by NTTD

Removing vertical lines on prints Attachments   (Pages: 1 2 3)

by nebbian
3,208 78 07/09/2017 08:14AM
Last Post by SJN

Extruder run differently with same configuration Attachments

by cthsieh
159 4 07/06/2017 05:23PM
Last Post by cthsieh

Which printer to build? Recommendations required

by Inhumierer
213 3 07/05/2017 10:56AM
Last Post by Inhumierer

Delta Calibration firmware for atmega + ramps 1.4

by VJain
736 18 07/02/2017 07:59AM
Last Post by VJain

About configuring the Marlin for Delta machine Attachments

by cthsieh
235 1 06/29/2017 01:15AM
Last Post by cthsieh

Cherry Pi III Is Available Attachments   (Pages: 1 ... 42 43 44)

by AndyCart
58,947 1,303 06/27/2017 05:18PM
Last Post by mkeveney

Custom Delta Build, problem with accuracy

by Nerveasy
530 6 06/14/2017 05:24AM
Last Post by Nerveasy

Flsun kossel delta printer problems

by tetris911
427 2 06/11/2017 06:15AM
Last Post by TW1ST3DG34R

Bed leveling Issue - Marlin

by phcella
308 2 06/10/2017 02:05PM
Last Post by LVD

Delta G33 Auto Level, Bed not leveled

by novio8
408 9 06/10/2017 06:36AM
Last Post by novio8

Folgertech Kossel 2020 kit, first try and success! Attachments

by dlc60
688 5 06/08/2017 09:45PM
Last Post by bradb

The "Flying Extruder" Mod   (Pages: 1 2 3 4 5)

by ähM_Key
13,875 135 06/08/2017 09:17AM
Last Post by jonathank

New Delta

by tlmxcpmpp
337 1 06/07/2017 12:41PM
Last Post by tlmxcpmpp

Delta Printer Portability

by FA-MAS
285 8 06/07/2017 12:36PM
Last Post by FA-MAS