Welcome! Log In Create A New Profile

Delta Machines

Rostock, Kossel, Simpson, 3DR, and more. See: http://reprap.org/wiki/Category:Delta. Previously named "Delta Robots and Stewart Platform"

Page 13 of 59 Pages:

11 121314 15

Forum List New Topic RSS

	Views	Posts	Last Post
Help! New delta G28 doesnt home. But moves all motors about 10mm opposite way by Jmtech	612	4	07/25/2017 03:39PM Last Post by Jmtech
Help! Delta refuse to get closer then 1mm to the bed by SlowFoot	594	1	07/25/2017 02:25PM Last Post by SlowFoot
KILLED. PRINTER HALTED solved... by tonyoses	5,152	3	07/23/2017 07:54PM Last Post by tonyoses
Ripple Eliminator by uvarovkv	2,098	17	07/19/2017 10:36PM Last Post by fredchan
Direct extrusion and Rostock mini by ax2013	755	8	07/18/2017 05:01PM Last Post by ax2013
Sintron Kossel Z height will not lower print head enough by Wibbles	516	3	07/18/2017 02:33PM Last Post by Wibbles
Delta (3DR Based) Will Not Move After G28 by Syko_Symatic	576	1	07/17/2017 06:34PM Last Post by Syko_Symatic
Can anyone explain how to use M666 Marlins? by disneytoy	18,417	24	07/15/2017 01:04PM Last Post by .AleX.
Delta calibration - backwards! by crenzi	679	1	07/15/2017 06:32AM Last Post by crenzi
Question about delta auto calibration and auto bed leveling by scanboy	1,985	4	07/13/2017 03:31PM Last Post by scanboy
Folgertech Kossel Rev A strangesness by SlowFoot	629	2	07/11/2017 03:04PM Last Post by Qdeathstar
The Anycubic Delta on AliExpress any good? (Pages: 1 2) by siddharta	9,307	34	07/10/2017 09:47AM Last Post by NTTD
Extruder run differently with same configuration by cthsieh	607	4	07/06/2017 08:23PM Last Post by cthsieh
Which printer to build? Recommendations required by Inhumierer	607	3	07/05/2017 01:56PM Last Post by Inhumierer
Delta Calibration firmware for atmega + ramps 1.4 by VJain	2,591	18	07/02/2017 10:59AM Last Post by VJain
About configuring the Marlin for Delta machine by cthsieh	796	1	06/29/2017 04:15AM Last Post by cthsieh
Custom Delta Build, problem with accuracy by Nerveasy	1,113	6	06/14/2017 08:24AM Last Post by Nerveasy
Flsun kossel delta printer problems by tetris911	1,158	2	06/11/2017 09:15AM Last Post by TW1ST3DG34R
Bed leveling Issue - Marlin by phcella	1,078	2	06/10/2017 05:05PM Last Post by LVD
Delta G33 Auto Level, Bed not leveled by novio8	1,880	9	06/10/2017 09:36AM Last Post by novio8
Folgertech Kossel 2020 kit, first try and success! by dlc60	2,116	5	06/09/2017 12:45AM Last Post by bradb
The "Flying Extruder" Mod (Pages: 1 2 3 4 5) by ähM_Key	29,027	135	06/08/2017 12:17PM Last Post by jonathank
New Delta by tlmxcpmpp	1,112	1	06/07/2017 03:41PM Last Post by tlmxcpmpp
Delta Printer Portability by blt3dp	795	8	06/07/2017 03:36PM Last Post by blt3dp
new flsun amazing delta by titeuf007	1,040	7	06/03/2017 05:29PM Last Post by titeuf007
Filament Dump Start Script - Cura by Mils24	3,421	22	06/03/2017 12:42PM Last Post by DjDemonD
Can Delta machines work without computers? by twwd	958	12	06/02/2017 04:55PM Last Post by dc42
Hexagon Hotend with Kossel Mini Review by DRTak	1,638	8	05/31/2017 06:23PM Last Post by DRTak
Any Tevo Little monster users around? by TheZombi122	1,926	5	05/29/2017 08:58PM Last Post by TheZombi122
New delta printer impossible to calibrate with firmware by w1k3	2,203	14	05/29/2017 10:06AM Last Post by chris33

Page 13 of 59 Pages:

11 121314 15

Delta Machines

The Anycubic Delta on AliExpress any good? (Pages: 1 2)

The "Flying Extruder" Mod (Pages: 1 2 3 4 5)