Welcome! Log In Create A New Profile

Advanced

Extruded Aluminum Frames

Cartesian XYZ machines with frames made of extruded aluminum, T-Slot, Makerslide, and more. See http://reprap.org/wiki/Category:Aluminum. Previously named "Extruded Aluminum"  
Subject Views Posts Last Post

Beware : Extruded profiles can be bended or twisted, while remaining standard !

by M_Xeno
7,830 4 02/04/2019 03:33PM
Last Post by gmedlicott

y carriage for mk3 4030 heatbed?

by emaayan
5,295 1 02/01/2019 06:59AM
Last Post by emaayan

Carbon tubes --> longer then 1 meter

by Arnix
5,246 1 01/23/2019 09:32AM
Last Post by Arnix

Linear Rail Cantilever printer build Attachments

by awratten
3,968 9 12/30/2018 07:58PM
Last Post by awratten

Sources for extruded aluminum profiles   (Pages: 1 2)

by MarcusWolschon
18,807 35 12/19/2018 05:13PM
Last Post by witor

4040 Open build profiles right angle joint - what's the best way? Attachments

by witor
2,743 3 12/19/2018 04:35PM
Last Post by witor

1 or 2 rails for y axis?

by witor
4,200 13 12/17/2018 08:06PM
Last Post by witor

Rep A Sketch Attachments

by Number_5
2,049 10 12/01/2018 09:45PM
Last Post by Number_5

Printer Design with Bearings on Extrusions

by gmedlicott
1,936 12 11/29/2018 01:20PM
Last Post by gmedlicott

Three point bed adjustment

by charlieRC
3,284 20 11/11/2018 12:58PM
Last Post by charlieRC

Ender 3 vs Malyan M150 (Wanhao i3 look-a-like)

by SaleB
1,866 2 11/10/2018 11:18AM
Last Post by Number_5

First build, having issues Attachments

by LFG
1,614 13 10/20/2018 10:05PM
Last Post by Dust

MiniMax: my experimental CoreXY Attachments

by o_lampe
2,086 9 09/23/2018 02:14AM
Last Post by o_lampe

Cutting extruded ali

by nod2
2,059 9 09/03/2018 07:07AM
Last Post by mcdanlj

X-axis Not homing after crash Flsun i3

by dolon
1,043 2 08/11/2018 02:24AM
Last Post by dolon

Black Beauty Build Log   (Pages: 1 2)

by gtj
6,184 50 07/19/2018 07:21PM
Last Post by gtj

Scrap yard run.... SCORE! Attachments

by the_digital_dentist
1,470 5 06/17/2018 11:26PM
Last Post by the_digital_dentist

Which side does the end-stops goes?

by lunar211
4,507 7 05/17/2018 01:49PM
Last Post by the_digital_dentist

Leadscrew driven XY gantry printer?

by klcjr89
5,748 12 03/25/2018 05:20PM
Last Post by gtj

Cheap-and-cheerful Taobao $150 knock-off running at 200mm/sec   (Pages: 1 2 3)

by lkcl
7,123 80 01/05/2018 10:33PM
Last Post by lkcl

RepRap Tevo Tornado/Cr-10

by masterviana
1,703 3 12/28/2017 06:28AM
Last Post by masterviana

Unable to complete my Tarantula due to dodgy parts!

by cheapo
1,520 3 12/23/2017 09:59AM
Last Post by cheapo

FLSUN I3 kit review   (Pages: 1 ... 4 5 6)

by R.G.
35,449 159 12/20/2017 08:54AM
Last Post by jnsbanman

flsun metal frame: configure.h

by wrapperz
2,922 3 10/26/2017 01:19AM
Last Post by wrapperz

help identifying controller board

by wrapperz
1,718 3 10/18/2017 06:37PM
Last Post by wrapperz

Prusa i3 MK3 extrusion

by Dust
6,313 12 10/04/2017 08:28AM
Last Post by MechaBits

Riki200   (Pages: 1 2 3 4 5)

by lkcl
10,561 123 09/11/2017 12:39AM
Last Post by lkcl

Z-axis homing not repeatable (prusa i3 from FLSUN)

by meekeech
2,131 1 08/17/2017 02:09AM
Last Post by meekeech

Z Axis Resets 15mm Above Bed

by dolon
1,442 3 08/15/2017 01:54AM
Last Post by dolon

My first Servo motor based 3d printer

by vova
25,167 24 08/03/2017 02:23PM
Last Post by 691175002