Welcome! Log In Create A New Profile

Advanced

Extruded Aluminum Frames

Cartesian XYZ machines with frames made of extruded aluminum, T-Slot, Makerslide, and more. See http://reprap.org/wiki/Category:Aluminum. Previously named "Extruded Aluminum"  
Subject Views Posts Last Post

Cheap-and-cheerful Taobao $150 knock-off running at 200mm/sec

by lkcl
65 1 05/25/2017 01:54AM
Last Post by lkcl

FLSUN I3 kit review   (Pages: 1 2 3 4 5)

by R.G.
9,208 141 05/22/2017 03:25PM
Last Post by lkcl

New build, pre-design questions, extrusions, shafts, dimensions, electronics

by SaleB
1,045 20 05/16/2017 04:22AM
Last Post by lkcl

This is a tank

by cwaa
1,400 10 05/15/2017 07:58AM
Last Post by cwaa

Help me improve rigidity of frame Attachments

by karandex
1,078 8 05/12/2017 10:01AM
Last Post by lkcl

linear rails advice for a 200x200 design

by lkcl
127 1 05/11/2017 10:21AM
Last Post by lkcl

Riki200

by lkcl
106 1 05/10/2017 04:21AM
Last Post by lkcl

Where to get 20x20mm aluminum extrusion   (Pages: 1 2)

by Doug1
14,109 37 05/02/2017 08:53AM
Last Post by robb_nl

Why is V-slot so much more expensive than T-slot

by Antscran
908 6 04/27/2017 01:03PM
Last Post by cwaa

cutting 8020 extrusions with a chop saw

by davedavedave
1,276 7 04/19/2017 02:50PM
Last Post by cwaa

New FlyingBear P902 issue

by Carl_S
307 2 04/17/2017 05:41AM
Last Post by Carl_S

End Stops?

by Rlewisrlou666
707 4 03/23/2017 06:33AM
Last Post by the_digital_dentist

FLSUN i3 Filament changeover

by wunderkind
421 1 03/22/2017 01:45PM
Last Post by wunderkind

MechaBits KraftWerk'r   (Pages: 1 2)

by MechaBits
2,533 48 01/25/2017 04:44AM
Last Post by MechaBits

Quadmax - a Mendelmax conversion

by Chri
642 1 12/28/2016 01:52AM
Last Post by Chri

Anodised Extruded Aluminium.

by Rlewisrlou666
653 4 10/19/2016 09:32AM
Last Post by Rlewisrlou666

Duet board wont connect to panelDUE and endstops

by 1andchin
1,103 9 09/06/2016 03:02AM
Last Post by DjDemonD

Mechanical End Stop Wiring Issue Mks 1.4 Board Attachments

by ca_resh
660 3 09/01/2016 01:46PM
Last Post by ca_resh

First Printer, 225mm^3 printer / mill combo build   (Pages: 1 2 3 4)

by Tired2
11,404 100 08/09/2016 08:47AM
Last Post by Tired2

Score another one for the Openbuilds

by Shank man
908 5 08/09/2016 02:38AM
Last Post by Shank man

POC printer Attachments

by deckingman
859 6 07/21/2016 11:49AM
Last Post by deckingman

New to this part of the forum Attachments

by wampablo
590 1 07/13/2016 12:42PM
Last Post by wampablo

My advice on buying Open Builds Vslot in UK

by deckingman
1,298 23 07/13/2016 11:05AM
Last Post by RyanL

Print bed printing down as aposed to printing up

by johnvictor
599 1 07/11/2016 08:44AM
Last Post by johnvictor

Building Questions

by ollyreprap
701 6 07/02/2016 01:12PM
Last Post by deckingman

Vertical Lines on my prints Attachments

by juanfly
751 5 06/28/2016 02:43AM
Last Post by Origamib

[BuildLog] HexRap | Extrusion based 3D-Printer

by TheHexaCube
883 6 06/06/2016 04:45PM
Last Post by Origamib

Measurements of Misumi 2020 and Hiwin MGN12 Attachments

by FA-MAS
981 8 05/29/2016 02:21PM
Last Post by Mikk36

Which rail size and car size for 2020 extrusions?

by drmaestro
1,097 16 05/21/2016 03:10PM
Last Post by drmaestro

Best way to change to linear rail system with minimum modification Attachments

by drmaestro
1,084 8 04/13/2016 01:57PM
Last Post by MechaBits