Welcome! Log In Create A New Profile

Advanced

Stepper Motors, Servo Motors, DC Motors

Discuss here what makes your printer moving. 
Subject Views Posts Last Post

interesting quirks with feedrate and new motor drivers.

by mrsour
214 2 06/08/2016 07:39AM
Last Post by mrsour

Identifing a damaged stepper

by Gaou
204 1 06/02/2016 09:57AM
Last Post by Gaou

how do i stop the motor shaft which has a load, from rotating when the power is shut off

by za
202 7 05/30/2016 08:01AM
Last Post by the_digital_dentist

Very jerky stepper movement

by Jelby-John
1,873 20 05/27/2016 07:24PM
Last Post by BioLumo

Resisting Voltage from Power Stage

by sullivnc
128 3 05/25/2016 12:07PM
Last Post by bobc

Voltage Rumba board

by Hans123456789
337 1 05/19/2016 05:01AM
Last Post by Hans123456789

Vibration at low speed

by Nikel
511 6 05/18/2016 03:16PM
Last Post by the_digital_dentist

Choice between two steppers

by jonawald
215 1 05/11/2016 09:03PM
Last Post by jonawald

C Driver not fully working

by Nikel
111 2 05/06/2016 02:09AM
Last Post by bobc

Help with Project List

by jr9820
142 4 05/04/2016 08:17PM
Last Post by cozmicray

DRV8825 "skipping" microsteps

by peepsalot
4,491 8 05/04/2016 01:55PM
Last Post by MrBaz

Stepper motor power supply

by Harmsobuk
1,180 4 04/27/2016 06:56AM
Last Post by the_digital_dentist

Stepper Motors from old Laser Printers

by nike357
1,228 14 04/25/2016 11:24PM
Last Post by nike357

Speed and torque calculation of stepper motor Attachments

by bobdxcool
486 2 04/23/2016 03:11PM
Last Post by dc42

Prusa i3 steppers

by Stoica
168 3 04/21/2016 04:54AM
Last Post by o_lampe

Motor with Fast rpm at the start and Slow rpm at the end

by Tawn
213 4 04/18/2016 11:33AM
Last Post by bobc

Motorcontrollers needing 5v, and RADDS 1.5 giving 3.3v

by Exinferis
194 1 04/18/2016 09:57AM
Last Post by Exinferis

Printer tremble

by Gaou
126 4 04/18/2016 01:07AM
Last Post by dc42

Cheapest place to get Nema 17 stepper motor?

by 3DMachiner
451 3 04/17/2016 10:31PM
Last Post by Gaou

RUMBA/A4988s w/24V result in motors working erratically

by rtrahms
1,034 8 04/01/2016 12:54AM
Last Post by dc42

Help Finding Drive/Controller

by sullivnc
156 7 03/30/2016 06:29AM
Last Post by dc42

Did anyone used linear hall sensors on BLDCs for position sensing?

by misan
2,139 25 03/30/2016 12:47AM
Last Post by misan

Needing Help With Egg Turner Project

by swtrpeter
173 2 03/26/2016 12:44AM
Last Post by Dust

Helpppp

by jam
133 3 03/23/2016 09:37AM
Last Post by jam

Ramps 1.4 x-axis broken

by canteen234
229 1 03/22/2016 05:36PM
Last Post by canteen234

Can I cover the back of the stepper motor

by ihaveworms
171 2 03/22/2016 09:46AM
Last Post by stephenrc

Stepper or brushed DC motor with sharp and fast turn

by viktor80
252 2 03/17/2016 01:18PM
Last Post by dc42

extruder acceleration/deceleration during printing

by friarfish
298 3 03/12/2016 02:52AM
Last Post by friarfish

buying parts for auto leveling

by zkent
234 3 03/01/2016 11:08AM
Last Post by zkent

How to calculate stepper motor power requirement?

by plankton
7,026 6 02/19/2016 12:45PM
Last Post by dc42