Welcome! Log In Create A New Profile

Advanced

Stepper Motors, Servo Motors, DC Motors

Discuss here what makes your printer moving. 
Subject Views Posts Last Post

Stepper any good for prusa

by ipecacd
938 1 12/01/2011 12:31AM
Last Post by ipecacd

Problem with L6228 Stepper Circuit Mbed Micro Attachments

by jhdgkss
934 3 11/29/2011 08:37PM
Last Post by JAYCON

Y Axis stepper erratic/vibrating/static while printing

by naples
1,651 5 11/26/2011 09:20AM
Last Post by bryanandaimee

Fried stepper drivers!

by T-Carbs
793 2 11/25/2011 11:25PM
Last Post by nophead

Getting gears off these motors I bought

by Thav
1,363 6 11/22/2011 09:14AM
Last Post by criswilson10

Useful Stepper Tutorial

by makeme
1,238 1 11/19/2011 09:11PM
Last Post by makeme

Overheating Stepper motors

by Architect
3,400 5 11/18/2011 10:39AM
Last Post by GeeksGoneBad

stepstick driver pb

by imprime3d
1,222 10 11/03/2011 12:37PM
Last Post by imprime3d

Is any of these good for reprap:ing?

by MikaelP
873 3 11/01/2011 03:14AM
Last Post by Traumflug

Dual driver, single microcontroller? Attachments

by danx3
934 5 10/31/2011 07:27AM
Last Post by marnargulus

Hissing sound on low-ohm stepper motor

by Traumflug
2,465 2 10/08/2011 02:10AM
Last Post by nophead

3d printing and 3d scanning now on egypt Attachments

by engalsapagh
1,024 1 09/06/2011 03:14AM
Last Post by engalsapagh

looking for a FAST stepper...

by rubin
7,755 10 09/05/2011 01:11PM
Last Post by rubin

Servos?

by Legot
695 2 08/21/2011 10:04PM
Last Post by VDX

Why not use this stepper driver?

by clooner
2,429 5 08/18/2011 11:56PM
Last Post by Traumflug

DC-DC converter to increase stepper voltage

by MtCS
1,148 2 08/15/2011 08:04AM
Last Post by Andrew Diehl

Bipolar Stepper driver with just 2 DACs and 2+1 mosfets - possible?

by ElectricMucus
1,749 3 07/27/2011 02:37PM
Last Post by ElectricMucus

E-recycler here, hoping to sell you motors.

by Nerfsmith
1,122 6 07/26/2011 04:14AM
Last Post by DeuxVis

stepper motion not smooth

by TheCase
2,900 5 07/25/2011 08:56PM
Last Post by TheCase

~27 volt steppers

by Ollie
838 4 06/20/2011 08:32AM
Last Post by Ollie

Geared stepper? Torque, resolution, heat, etc

by 3dp_dude
1,049 3 06/10/2011 08:20AM
Last Post by mrfahrenheit94

New source of SY42STH47-1206A

by RyanTM
3,163 7 06/04/2011 10:42AM
Last Post by spad007

Would this Stepper work for a Prusa

by cnc1965
1,793 4 03/17/2011 05:34AM
Last Post by jgilmore

low torque

by karandex
1,771 17 03/12/2011 11:05PM
Last Post by karandex

.9 degree steppers. Do I need to change settings anywhere?

by Buback
6,572 18 03/02/2011 09:36AM
Last Post by Buback

NEMA 23 6 wire Unipolar with Gen 6 electronics?

by Axim
1,956 3 02/08/2011 06:04PM
Last Post by jgilmore

EAD lh2322-p300a13

by rkoeppl
2,634 6 02/04/2011 10:50PM
Last Post by rkoeppl

Ebay Stepper Motors (datasheet included).

by elgin.owens
2,513 3 12/16/2010 10:48AM
Last Post by elgin.owens

Blobbed hot end from printer parts & shapelock Attachments

by jgilmore
1,504 3 11/16/2010 10:58AM
Last Post by jgilmore

6v steppers

by dissidence
2,009 8 10/31/2010 05:52PM
Last Post by dissidence