Welcome! Log In Create A New Profile

Stepper Motors, Servo Motors, DC Motors

Discuss here what makes your printer moving.

Page 16 of 22 Pages:

14 151617 18

Forum List New Topic RSS

	Views	Posts	Last Post
modifying the cheap stepper motor Howard Ind. 1-19-4200 from unipolar motor to bipolar by tenbaht	2,442	2	11/04/2013 06:39PM Last Post by ansel
Servo Motor by Servo	1,337	2	10/27/2013 04:15PM Last Post by bobc
3 Bad steppers, bad DIY breakout, or wrong settings in config.h? by 1HzCoder	1,396	3	10/12/2013 10:54AM Last Post by Ed
need to buy crimp housing for wires by ddock	747	3	10/12/2013 10:44AM Last Post by Ed
Berger Lahar RDM 599/50 5 phase motor and Berger Lahar D450.01 Driver by cpalha	955	1	10/11/2013 01:42AM Last Post by cpalha
Unidentified Japan Servo steppers by luismanson	2,899	12	10/10/2013 01:44PM Last Post by NoobMan
Some general motor questions by SamS	752	2	10/09/2013 03:37PM Last Post by bryanandaimee
voltage/ohm selection by luismanson	955	5	10/02/2013 08:05AM Last Post by luismanson
Urgent Mendel90 Question by Andrico	789	3	09/27/2013 08:39AM Last Post by nophead
Arg! Can't get these suckers to step! by attrezzopox	2,908	6	09/19/2013 12:15PM Last Post by mkaisercross
Stepper Motor juddering and reversing direction by MartinB	2,164	3	09/19/2013 05:26AM Last Post by MartinB
Blocked Nema17 Stepper motor by Vancoillie	942	3	09/19/2013 03:17AM Last Post by waitaki
TB6600 wiring help by varunme	1,865	5	09/13/2013 01:00PM Last Post by varunme
Linear actuator and stepper motor by SR92	2,700	4	09/12/2013 12:30PM Last Post by EddieAuto
NEMA 17 VM42HT47-1684A by zerg	821	3	09/04/2013 06:35PM Last Post by zerg
Rewiring 5-wire steppers? by droftarts	3,547	6	09/04/2013 11:47AM Last Post by Yvan256
Finer step angle by Yamster	1,746	8	08/18/2013 11:05PM Last Post by Yamster
Motor Friction torque by SR92	850	1	07/29/2013 06:02PM Last Post by SR92
Help Inconsistent Steppers by Fabbers	882	1	07/29/2013 05:35PM Last Post by Fabbers
Melzi Drive Capacity by drcymru	850	2	07/27/2013 01:10PM Last Post by bryanandaimee
nema 14 vs nema 17 at same current by nikbjo	4,972	2	07/27/2013 01:04PM Last Post by bryanandaimee
Stepper Motor Connector? by iVoid	3,553	4	07/24/2013 10:35PM Last Post by iVoid
A3995 stepper driver for RAMPS by renowijoyo	730	3	07/22/2013 03:05PM Last Post by TopherMan
Stepper Motors at Liquidation Prices! by machmotion	2,324	7	07/21/2013 09:42PM Last Post by SheldonE
Need a stepper driver recommendation by wacoe96	1,095	4	07/21/2013 05:52AM Last Post by Traumflug
Moons 17HD Stepper Wiring Problem by derekmjenkins	1,420	1	07/17/2013 06:29PM Last Post by derekmjenkins
Applied Motion stepper configuration by dhissink	1,094	3	07/17/2013 09:42AM Last Post by derekmjenkins
Stepper, torque, volts, pps by Coolerooney	3,906	5	07/14/2013 05:26AM Last Post by Coolerooney
Programming using NanoPro from Nanotec by FCCBFC	2,010	5	07/12/2013 05:59PM Last Post by VDX
Axis X - Stepper Motor Problem by niksoley	1,081	3	07/07/2013 03:40PM Last Post by niksoley

Page 16 of 22 Pages:

14 151617 18