Welcome! Log In Create A New Profile

Advanced

Stepper Motors, Servo Motors, DC Motors

Discuss here what makes your printer moving. 
Subject Views Posts Last Post

2ch remote with l298n and nema 17 connection Attachments

by vojotic
34 1 03/29/2015 10:38AM
Last Post by vojotic

Advice for a wear resistant extruder cable.

by corngolem
37 1 03/29/2015 03:22AM
Last Post by corngolem

Gen6 Electronics Stepper Motor Pin Outs

by andy_tratter
36 1 03/28/2015 09:28AM
Last Post by andy_tratter

Miniature Couplings with variable diameters

by dannybaws
114 3 03/24/2015 10:25AM
Last Post by dannybaws

Disable the servo when the printer is idle?

by fractal5
69 1 03/21/2015 02:12PM
Last Post by fractal5

Clunking steppers at end of move command DRV8825

by alan richard
83 1 03/20/2015 05:34AM
Last Post by alan richard

Ardunio sketch advice!

by mrsmith91
105 1 03/18/2015 06:12AM
Last Post by mrsmith91

Reprap test code explanation

by mrsmith91
98 1 03/16/2015 10:37AM
Last Post by mrsmith91

Problem with StepStick and 1.2A Stepper

by teoemo
108 1 03/09/2015 08:36PM
Last Post by teoemo

A4988 driver not working near a relay circuit

by anto
105 3 03/03/2015 08:09AM
Last Post by dc42

Sourcing stepper motors for Rostock mini pro

by Zxenop
166 8 03/01/2015 01:49PM
Last Post by Zxenop

Change of motors

by Kozmik_Kat
120 2 02/27/2015 09:10AM
Last Post by Kozmik_Kat

To Turn Fast or Slow, That is My Question

by matt-in-georgia
159 2 02/21/2015 09:27AM
Last Post by Traumflug

No retract with DRV8825 on Rumba

by razzle
179 4 02/20/2015 02:50AM
Last Post by Traumflug

Stepper motor driver is hot.

by karagad
287 2 02/01/2015 10:39PM
Last Post by Dust

Stepper as programmable uniform torque load in test rig

by cumfy
163 2 01/30/2015 03:32AM
Last Post by Traumflug

3 phase stepper with 1000 encoder

by h3ndrix
215 3 01/25/2015 04:37AM
Last Post by h3ndrix

Stepper motor doesn't work

by karagad
295 4 01/23/2015 10:37PM
Last Post by Dust

Servo motors on Prusa i3

by misan
342 8 01/20/2015 03:42PM
Last Post by Ezrec

Open Source DC or BLDC controller

by MachineHum
293 3 01/18/2015 08:42PM
Last Post by Ezrec

6 lead motor for RAMPS?

by kryptomaniac
203 2 01/12/2015 10:39PM
Last Post by enif

Axis steppers stop after first command Attachments

by twofieros
207 5 01/09/2015 04:38PM
Last Post by twofieros

Stepper motor works from prontoface, but not when printing

by tellblom
207 3 01/08/2015 02:13PM
Last Post by nophead

Motors only vibrate but will not turn

by surfacelane
1,526 12 01/03/2015 01:23PM
Last Post by psneddon

Extruder stepper missing steps..

by Replace
279 6 01/03/2015 11:46AM
Last Post by Replace

Servo Driver compatible with RAMPS (STEP/DIR)

by unfold
1,656 5 01/03/2015 06:59AM
Last Post by unfold

What voltage specs for Nema17 on Ramps ?

by Replace
325 4 01/02/2015 06:59AM
Last Post by dc42

XY table from DVD drives - how to make a grbl-compatible stepper driver?

by emes
303 3 12/23/2014 01:12PM
Last Post by emes

86HS120 motors and board connections for driver

by htekin
2,988 4 12/14/2014 07:04AM
Last Post by george4657

Extruder stepper freeze when hitting extrude in pronterface

by aunueget
246 7 12/11/2014 07:31AM
Last Post by aunueget