Welcome! Log In Create A New Profile

Advanced

Sanguino(lolu)

The Sanguino is an extension of the popular Arduino board designed and developed by Zach Hoeken et.al. for the RepRap Research Foundation. 
Subject Views Posts Last Post

Sanguino into Arduino

by Bill_of_the_North
2,616 3 01/12/2023 02:57PM
Last Post by Bill_of_the_North

Verifying bootloader and/or firmware on Sanguinololou with ATMega1284P

by cpnbnanamn
5,728 15 05/16/2022 07:37PM
Last Post by Drink water

Melzi Ardentissimo 1.1.9 marlin config

by yaboo
3,046 1 12/20/2021 09:58AM
Last Post by yaboo

Using Pin 29 on a Creality v1.1.4 Melzi Board...

by R23D
5,206 2 03/04/2021 10:20AM
Last Post by R23D

Melzi 2.0 with Marlin 1.1.9 endstops are not working

by vinibali
6,239 8 01/03/2021 05:50AM
Last Post by Dust

MELZI Signals query Attachments

by Supermec
6,108 2 09/28/2020 06:29PM
Last Post by Anonymous User

dual extruder

by badhank
6,078 2 09/28/2020 06:29PM
Last Post by Anonymous User

My mods for curing 5V USB/7805 problems on Sanguinololu 1.3a Attachments   (Pages: 1 2)

by enif
10,902 31 09/26/2020 03:47AM
Last Post by rajubhaiya

Melzi lost USB connection

by MCcarman
6,796 3 09/22/2020 03:03PM
Last Post by Anonymous User

Changing the hot-end mosfet on my sanguinololu

by Nabbissimo
5,749 2 09/22/2020 03:02PM
Last Post by Anonymous User

How to install a bootloader on a Sanguinololu 1.3a with 1284P in 2019+

by ChristianKxng
8,402 19 08/30/2020 11:41PM
Last Post by Machac

Sanguinololu 1.3a, Marlin 1.1.9

by MKSA
15,286 12 08/30/2020 11:39PM
Last Post by Machac

What is this board and can it run Marlin 1.1.8

by NozzleMover
8,387 25 08/23/2020 03:10PM
Last Post by NozzleMover

backup installed firmware?

by Adrian
48,033 16 08/20/2020 10:04AM
Last Post by Anonymous User

Uploading marlin via Arduino as ISP in platformio

by Dust
6,461 1 04/24/2020 12:04PM
Last Post by Dust

Verification failure after upload?

by jamesshuang
32,337 19 03/12/2020 01:05PM
Last Post by NozzleMover

Reprap Discount Smart Controller Not Working

by Flightless
8,300 8 01/10/2020 08:01PM
Last Post by Roberts_Clif

Height of printed part is short +(Is it possible to supply a 20a current to the board without the heating bed? )

by booboo4641
5,065 3 01/01/2020 09:13PM
Last Post by Dust

Bed thermistor failure. Negative temperature readout (please help)

by TBK2020
5,692 8 12/25/2019 02:53AM
Last Post by Ohmarinus

Melzi 2.0 connectivity issues

by HyraxAttax
5,518 3 06/22/2019 08:11PM
Last Post by HyraxAttax

LCD Display probleme after upgrading firmware Attachments

by jiefel
5,981 4 06/06/2019 08:56AM
Last Post by meo_udon

BLTouch not working on Anet A8

by lukaspanic
6,967 6 02/06/2019 04:33PM
Last Post by Roberts_Clif

RepRap Discount Full Graphic LCD clone on Melzi 2.0 success. Attachments

by mr.sneezy
10,136 7 08/23/2018 01:02PM
Last Post by nkuck

RepRap discount full graphic LCD for sanguinololu

by Nabbissimo
5,869 4 02/16/2018 12:50PM
Last Post by Nabbissimo

Melzi - Heated bed is being powered via the USB cable

by remondo
6,405 3 08/22/2017 10:27AM
Last Post by remondo

[solved] Max current on melzi v2.0

by alvinflumox
6,152 3 07/09/2017 05:20PM
Last Post by alvinflumox

Sanguinololu Rev 1.3a - how to load firmware

by Dam
13,234 24 05/24/2017 06:59PM
Last Post by JustSumGuy

2nd Extruder Upgrade for rev 1.3a ?

by Chri
7,065 7 04/07/2017 02:28PM
Last Post by papakel

Sanguinololu 1.3a, Marlin and Sainsmart lcd

by mtsnow
9,812 16 02/06/2017 02:08PM
Last Post by papakel

Questions about component choice

by spaceorange12
6,016 6 02/03/2017 11:03AM
Last Post by spaceorange12