Welcome! Log In Create A New Profile

Firmware - experimental, borrowed, and future

Page 9 of 13 Pages:

7 8910 11

Forum List New Topic RSS

	Views	Posts	Last Post
marlin feature request / idea: speedometer (gcode command that returns the current speed) by zachnfine	2,345	6	08/31/2012 06:10PM Last Post by zachnfine
Teacup does not seem to notice limit switches by frits297	1,997	7	08/18/2012 05:17AM Last Post by Traumflug
Gen7 V1.3.1 board with Marlin by bethebeer	1,596	4	08/12/2012 05:44PM Last Post by jamesdanielv
Motors by coyoteln	1,082	3	08/07/2012 04:42AM Last Post by Traumflug
SD bugs in Marlin? by fbeachler	1,575	4	08/05/2012 02:32PM Last Post by nophead
serial pass through Protocol by cortex	1,462	5	07/29/2012 06:11PM Last Post by cortex
MELZI Marlin pins by nophead	3,587	4	07/23/2012 10:20AM Last Post by nophead
New and improved comms protocol? by bobc	1,103	1	07/10/2012 08:48PM Last Post by bobc
lib to parse text file from SDCard, for config of RepRap printers by casainho	6,207	4	07/10/2012 01:24PM Last Post by XOR
Prints hanging at same GCode line with Teacup + Gen7 by alianmac	3,503	30	07/08/2012 09:46AM Last Post by François Delègue
Modification for rotational axis by MathijsF	1,292	2	07/07/2012 06:38AM Last Post by Traumflug
Exchange crystal to 18.432 MHz by ado	1,801	1	06/30/2012 07:22PM Last Post by ado
Teacup Auto Bed Leveling by bethebeer	2,345	2	06/27/2012 05:51AM Last Post by Traumflug
Teacup Firmware on a Gen6 electronics: axes moving? by Traumflug	1,135	1	06/21/2012 04:19PM Last Post by Traumflug
Teacup problem: Temperature scaled incorrectly? by aeram00	1,177	2	06/20/2012 07:06AM Last Post by Traumflug
Enable cooling fan when starting to heat extruder. by zelogik	3,278	4	06/16/2012 03:02AM Last Post by zelogik
Teacup/Gen7 buggy print with M101 & M103 by François Delègue	1,457	6	06/15/2012 10:40AM Last Post by François Delègue
Teacup supported on Sanguinololu? by Pointedstick	2,784	24	06/09/2012 07:27AM Last Post by Traumflug
Sprinter narrow pulse width by macegr	1,954	7	05/30/2012 02:13AM Last Post by appydavid1
Teacup Firmware. Was "FiveD on Arduino". by SebastienBailard	4,520	10	04/26/2012 05:09AM Last Post by Traumflug
odd x/y flip? by se5a	1,275	2	04/09/2012 07:35PM Last Post by stefanst
Repetier PID settings and thermistor tables by miro87043	7,991	5	04/01/2012 03:22PM Last Post by miro87043
Teacup compile error by stefanst	1,829	6	04/01/2012 06:58AM Last Post by Traumflug
Custom firmware - how to interpret feedrate by torur.strom	1,487	7	03/31/2012 09:36AM Last Post by bobc
Teacup firmware configuration - axis wont move by Roel	1,476	3	03/26/2012 11:26AM Last Post by Mendelfanatics
teacup: y axis periodically looses steps at defined positions in upper layers by mindfab	997	2	03/22/2012 01:01PM Last Post by mindfab
Printrboard Firmware by kang9468	1,278	2	03/21/2012 12:22PM Last Post by bobbintb
Teacup with fan? by destroyer2012	1,455	3	03/11/2012 02:31PM Last Post by destroyer2012
h-bot configuration by Snaka	1,462	1	03/07/2012 09:30PM Last Post by Snaka
Configuring Marlin for a 328 by Andrew Diehl	3,899	24	03/04/2012 09:19AM Last Post by jamesdanielv

Page 9 of 13 Pages:

7 8910 11