Welcome! Log In Create A New Profile

Advanced

Firmware - experimental, borrowed, and future

Subject Views Posts Last Post

Curved paths

by frankvdh
1,761 18 05/28/2015 04:29PM
Last Post by frankvdh

Leveling a particular area based off the current print's size

by kasper219
1,446 4 05/22/2015 05:45AM
Last Post by Wurstnase

Teacup_Firmware: How can i add other board to the firmware?

by tatubias
2,023 2 05/19/2015 08:46AM
Last Post by tatubias

manage_heater not updated during long moves

by Gosa
1,384 6 05/16/2015 03:47PM
Last Post by dc42

Adding support for up to 16 added temp sensors???

by kasper219
1,429 4 05/09/2015 09:16AM
Last Post by kasper219

marlin(arduino mega) strange G code explanations Attachments

by hihijudy
1,480 1 05/05/2015 04:58AM
Last Post by hihijudy

Teacup - temperature control and safety

by mogul
1,439 1 05/02/2015 05:41AM
Last Post by mogul

Arduino MEGA 2650 Temperature overhead

by Smart
1,420 6 04/30/2015 04:48AM
Last Post by Smart

Firmware architecture question trajectory planning

by nilrods
1,527 9 04/22/2015 10:28AM
Last Post by ambrop7

Assigning a new pin for the controller fan

by oscarte
1,415 1 04/21/2015 10:45AM
Last Post by oscarte

Dual Y-Axis Endstops Auto Squaring Marlin/Teacup

by Ironaxe
1,217 2 04/19/2015 08:41PM
Last Post by MM/S^2

manual one dir Y axis

by vangalvin
1,406 1 04/18/2015 09:17AM
Last Post by vangalvin

Including Mechanical Brake in Marlin-Software on RUMBA Board

by karl.ranseier
1,909 2 04/09/2015 04:45AM
Last Post by karl.ranseier

Problem temperature keeps raising

by Donato
1,387 1 04/08/2015 03:34PM
Last Post by Donato

Uarm based 3D printer

by tomfrombelgium
1,211 3 04/02/2015 11:03AM
Last Post by ekaggrat

What is the first file called when Marlin begins printing?

by Evil Monkey
1,487 6 03/29/2015 06:25PM
Last Post by Evil Monkey

Including Quadrature Encoder - PID positioning of DC motors into Teacup_Firmware

by unix_guru
1,667 4 03/27/2015 05:06AM
Last Post by unix_guru

borrowed (thermistor for toaster reflow) need help

by terramir
1,423 7 03/26/2015 10:33AM
Last Post by dc42

Marlin 32bit high step_rate

by Wurstnase
1,650 12 03/24/2015 10:14AM
Last Post by Wurstnase

start filament rejection Attachments

by lolohtl
1,144 1 03/22/2015 12:59PM
Last Post by lolohtl

Looking for an easily modifiable 'bare-bones' firmware.

by Capo
972 10 03/08/2015 03:57AM
Last Post by Capo

Changing bay on RUMBA motion controller for Extruder Stepper Driver

by SkiBum326
1,116 2 03/07/2015 08:23PM
Last Post by cat.farmer

Marlin 1.03 appeared and disapeared

by gordonendersby
1,103 2 03/06/2015 11:41AM
Last Post by gordonendersby

Help adding push button input to jog/ retract extruder for RAMPS

by alan richard
1,117 3 03/06/2015 09:08AM
Last Post by alan richard

Marlin Error:Thermal Runaway, system stopped! Heater_ID: 9

by Miamicraft
1,526 1 03/01/2015 03:41PM
Last Post by Miamicraft

bariCUDA Paste Extruder Support, Marlin

by jessicabrenner
980 1 02/24/2015 12:26AM
Last Post by jessicabrenner

Marlin endstop read

by luismanson
734 3 02/22/2015 12:11PM
Last Post by luismanson

I'm looking for a PostProcessor for SprutCam, that will output Gcode for Marlin

by dailafing
925 4 02/22/2015 04:24AM
Last Post by Traumflug

Help needed compiling Teacup_Firmware_Teensy3

by unix_guru
793 5 02/12/2015 02:00PM
Last Post by Traumflug

how change pins of full graphic smart controller in repetier firmware.

by snype
931 1 01/22/2015 02:56PM
Last Post by snype