Welcome! Log In Create A New Profile

Advanced

Firmware - experimental, borrowed, and future

Subject Views Posts Last Post

Leveling mode to move extruder to four corners

by ronhogwarts
1,199 1 07/19/2015 05:46AM
Last Post by ronhogwarts

Adding a custom G-Code case in firmware Marlin

by kasper219
1,668 4 07/07/2015 01:59PM
Last Post by jessicabrenner

Teacup on Sanginololu under Win 7 Attachments   (Pages: 1 2)

by OSUFlatland
1,851 41 07/03/2015 04:59PM
Last Post by OSUFlatland

Getting more speed out of Arduino Mega

by TESKAn
1,656 15 06/24/2015 05:43AM
Last Post by Wurstnase

Raise extruder on stop print

by casperen
1,379 1 06/16/2015 09:27AM
Last Post by casperen

reading gcode file from sdcard in cpp other than using gcodes

by prasunjoshi
1,309 2 06/15/2015 11:41PM
Last Post by thetazzbot

Curved paths

by frankvdh
1,615 18 05/28/2015 04:29PM
Last Post by frankvdh

Leveling a particular area based off the current print's size

by kasper219
1,418 4 05/22/2015 05:45AM
Last Post by Wurstnase

Teacup_Firmware: How can i add other board to the firmware?

by tatubias
1,929 2 05/19/2015 08:46AM
Last Post by tatubias

manage_heater not updated during long moves

by Gosa
1,354 6 05/16/2015 03:47PM
Last Post by dc42

Adding support for up to 16 added temp sensors???

by kasper219
1,389 4 05/09/2015 09:16AM
Last Post by kasper219

marlin(arduino mega) strange G code explanations Attachments

by hihijudy
1,443 1 05/05/2015 04:58AM
Last Post by hihijudy

Teacup - temperature control and safety

by mogul
1,400 1 05/02/2015 05:41AM
Last Post by mogul

Arduino MEGA 2650 Temperature overhead

by Smart
1,366 6 04/30/2015 04:48AM
Last Post by Smart

Firmware architecture question trajectory planning

by nilrods
1,438 9 04/22/2015 10:28AM
Last Post by ambrop7

Assigning a new pin for the controller fan

by oscarte
1,352 1 04/21/2015 10:45AM
Last Post by oscarte

Dual Y-Axis Endstops Auto Squaring Marlin/Teacup

by Ironaxe
1,109 2 04/19/2015 08:41PM
Last Post by MM/S^2

manual one dir Y axis

by vangalvin
1,357 1 04/18/2015 09:17AM
Last Post by vangalvin

Marlin code for scissor lift z-axis

by OoiTY
2,099 7 04/12/2015 03:42AM
Last Post by boy007

Including Mechanical Brake in Marlin-Software on RUMBA Board

by karl.ranseier
1,859 2 04/09/2015 04:45AM
Last Post by karl.ranseier

Problem temperature keeps raising

by Donato
1,357 1 04/08/2015 03:34PM
Last Post by Donato

Uarm based 3D printer

by tomfrombelgium
1,156 3 04/02/2015 11:03AM
Last Post by ekaggrat

What is the first file called when Marlin begins printing?

by Evil Monkey
1,411 6 03/29/2015 06:25PM
Last Post by Evil Monkey

Including Quadrature Encoder - PID positioning of DC motors into Teacup_Firmware

by unix_guru
1,437 4 03/27/2015 05:06AM
Last Post by unix_guru

borrowed (thermistor for toaster reflow) need help

by terramir
1,331 7 03/26/2015 10:33AM
Last Post by dc42

Marlin 32bit high step_rate

by Wurstnase
1,442 12 03/24/2015 10:14AM
Last Post by Wurstnase

start filament rejection Attachments

by lolohtl
1,099 1 03/22/2015 12:59PM
Last Post by lolohtl

Looking for an easily modifiable 'bare-bones' firmware.

by Capo
914 10 03/08/2015 03:57AM
Last Post by Capo

Changing bay on RUMBA motion controller for Extruder Stepper Driver

by SkiBum326
1,010 2 03/07/2015 08:23PM
Last Post by cat.farmer

Marlin 1.03 appeared and disapeared

by gordonendersby
1,045 2 03/06/2015 11:41AM
Last Post by gordonendersby