Welcome! Log In Create A New Profile

Advanced

Firmware - experimental, borrowed, and future

Subject Views Posts Last Post

Adding a custom G-Code case in firmware Marlin

by kasper219
81 2 05/26/2015 04:26PM
Last Post by MagoKimbra

Project: Teacup Firmware   (Pages: 1 ... 51 52 53)

by Triffid_Hunter
78,198 1,581 05/25/2015 10:11AM
Last Post by theothermike

Leveling a particular area based off the current print's size

by kasper219
151 4 05/22/2015 05:45AM
Last Post by Wurstnase

Teacup_Firmware: How can i add other board to the firmware?

by tatubias
111 2 05/19/2015 08:46AM
Last Post by tatubias

manage_heater not updated during long moves

by Gosa
97 6 05/16/2015 03:47PM
Last Post by dc42

Adding support for up to 16 added temp sensors???

by kasper219
142 4 05/09/2015 09:16AM
Last Post by kasper219

marlin(arduino mega) strange G code explanations Attachments

by hihijudy
153 1 05/05/2015 04:58AM
Last Post by hihijudy

Teacup - temperature control and safety

by mogul
156 1 05/02/2015 05:41AM
Last Post by mogul

Arduino MEGA 2650 Temperature overhead

by Smart
192 6 04/30/2015 04:48AM
Last Post by Smart

Marlin4Due   (Pages: 1 2)

by Wurstnase
732 34 04/28/2015 09:10AM
Last Post by tadawson

Firmware architecture question trajectory planning

by nilrods
382 9 04/22/2015 10:28AM
Last Post by ambrop7

Assigning a new pin for the controller fan

by oscarte
198 1 04/21/2015 10:45AM
Last Post by oscarte

Dual Y-Axis Endstops Auto Squaring Marlin/Teacup

by Ironaxe
915 2 04/19/2015 08:41PM
Last Post by MM/S^2

manual one dir Y axis

by vangalvin
249 1 04/18/2015 09:17AM
Last Post by vangalvin

Project: APrinter firmware

by ambrop7
812 5 04/17/2015 04:14PM
Last Post by AndrewBCN

Marlin code for scissor lift z-axis

by OoiTY
1,749 7 04/12/2015 03:42AM
Last Post by boy007

Including Mechanical Brake in Marlin-Software on RUMBA Board

by karl.ranseier
891 2 04/09/2015 04:45AM
Last Post by karl.ranseier

Problem temperature keeps raising

by Donato
308 1 04/08/2015 03:34PM
Last Post by Donato

Uarm based 3D printer

by tomfrombelgium
527 3 04/02/2015 11:03AM
Last Post by ekaggrat

What is the first file called when Marlin begins printing?

by Evil Monkey
337 6 03/29/2015 06:25PM
Last Post by Evil Monkey

Including Quadrature Encoder - PID positioning of DC motors into Teacup_Firmware

by unix_guru
510 4 03/27/2015 05:06AM
Last Post by unix_guru

borrowed (thermistor for toaster reflow) need help

by terramir
384 7 03/26/2015 10:33AM
Last Post by dc42

Marlin 32bit high step_rate

by Wurstnase
1,080 12 03/24/2015 10:14AM
Last Post by Wurstnase

start filament rejection Attachments

by lolohtl
394 1 03/22/2015 12:59PM
Last Post by lolohtl

Looking for an easily modifiable 'bare-bones' firmware.

by Capo
500 10 03/08/2015 03:57AM
Last Post by Capo

Changing bay on RUMBA motion controller for Extruder Stepper Driver

by SkiBum326
463 2 03/07/2015 08:23PM
Last Post by cat.farmer

Marlin 1.03 appeared and disapeared

by gordonendersby
484 2 03/06/2015 11:41AM
Last Post by gordonendersby

Help adding push button input to jog/ retract extruder for RAMPS

by alan richard
468 3 03/06/2015 09:08AM
Last Post by alan richard

Marlin Error:Thermal Runaway, system stopped! Heater_ID: 9

by Miamicraft
608 1 03/01/2015 03:41PM
Last Post by Miamicraft

bariCUDA Paste Extruder Support, Marlin

by jessicabrenner
564 1 02/24/2015 12:26AM
Last Post by jessicabrenner