Welcome! Log In Create A New Profile

Firmware - mainstream and related support

Page 38 of 42 Pages:

36 373839 40

Forum List New Topic RSS

	Views	Posts	Last Post
gen6 firmware by dave86	1,236	2	02/21/2012 10:38AM Last Post by bcndynamics
Java Host Sprinter - some setup issues by jbayless	1,446	1	02/20/2012 12:23AM Last Post by jbayless
Teacup incorrect response to M105 command by jbayless	1,719	4	02/19/2012 02:13PM Last Post by jbayless
Can't compile Teacup firmware by BobL	2,562	11	02/18/2012 07:55PM Last Post by jbayless
Odd behaviour with Sprinter firmware by ksmith5135	948	1	02/15/2012 10:00AM Last Post by ksmith5135
5D on gen4 by proctor	958	1	02/09/2012 06:09PM Last Post by proctor
Sprinter axis_steps_per_unit settings for SAE RepRap Prusa by emorning	5,358	6	02/08/2012 04:59PM Last Post by Ahasuerus
Extruder stepper rapid oscillations (Sprinter) by Edon	1,284	2	02/08/2012 08:03AM Last Post by VDX
Heat and false temperature reading by Kalle	910	1	02/04/2012 03:33PM Last Post by Kalle
Heat but no temperature reading! by Rico	1,070	3	02/04/2012 07:30AM Last Post by Kalle
Sprinter uploads then turns the extruder by roygpa	982	3	02/03/2012 03:26PM Last Post by jezmy
Changing from FiveD firmware to Marlin - A few questions about configuration.h values by Flackster	2,225	4	02/02/2012 07:45AM Last Post by Flackster
PCB Heatbed by windcatcher	3,239	11	01/28/2012 04:14AM Last Post by Traumflug
arduino 1.0 and sprinter by dissidence	2,171	4	01/28/2012 03:04AM Last Post by windcatcher
Y axe (only one direction) by DrimIsen	1,165	2	01/25/2012 10:28AM Last Post by rhmorrison
Axis stops moving after G91 by _Alex_	892	1	01/22/2012 06:16AM Last Post by _Alex_
Negative X,Y,Z values allowed? by misan	3,520	3	01/20/2012 02:56AM Last Post by misan
[solved] cant move z with sprinter firmware by zg_bot	1,322	8	01/12/2012 12:01AM Last Post by zg_bot
Z axis not working with Marlin by miro87043	1,994	3	01/11/2012 05:57PM Last Post by Ben Howes
Prints stop after some unknown number of commands by dazed.dnc	2,245	27	01/11/2012 11:24AM Last Post by jamesdanielv
Speed differences in Sprinter by Albert384	1,785	6	01/11/2012 10:54AM Last Post by jamesdanielv
Axis unable to change directions by TheWyliestCoyote	1,255	3	01/10/2012 10:45PM Last Post by TheWyliestCoyote
Is there an Idiots guide to programming the Arduino? by Chompalot	1,364	5	01/04/2012 02:14PM Last Post by Chompalot
Sanguinololu 1.3A, Sprinter (latest from git) no extruder by javanree	2,031	10	01/03/2012 02:26PM Last Post by javanree
serial lcd by dissidence	1,329	5	01/02/2012 08:29AM Last Post by dissidence
Sprinter firmware, All 3 axis going twice the distance by QFE24	1,773	4	01/01/2012 05:53PM Last Post by martinprice2004
RepRap Software Wont Open With Gen 6 by andy_tratter	1,306	4	12/24/2011 07:03PM Last Post by Codebreaker
Y skips with marlin not sprinter by ambiguousphoton	1,569	5	12/24/2011 05:17AM Last Post by Traumflug
Gen7 and Teacup Config.h setup check by foshon	1,348	3	12/20/2011 04:39AM Last Post by foshon
Homing direction on a Mendel/ FiveD firmware by hessel_swart	1,060	2	12/16/2011 06:08AM Last Post by Traumflug

Page 38 of 42 Pages:

36 373839 40