Welcome! Log In Create A New Profile

Firmware - mainstream and related support

Page 28 of 42 Pages:

26 272829 30

Forum List New Topic RSS

	Views	Posts	Last Post
Controlling RAMBO Mosfet Output by fmeroney	832	2	11/12/2013 01:01PM Last Post by fmeroney
Teacup avrdude verification error by awmt102	985	5	11/12/2013 08:29AM Last Post by Traumflug
Regulating extruding temperature based on volume by marton	509	1	11/12/2013 06:51AM Last Post by marton
Marlin acceleration and jerk settings help by Phizinza	2,101	1	11/11/2013 02:12AM Last Post by Phizinza
separate steps per rotation X Y axis in marlin by harmvdn	1,207	5	11/05/2013 04:01AM Last Post by harmvdn
Cannot flash firmware to Gen6 board by tbarends	929	2	11/04/2013 08:07AM Last Post by slymike
Marlin and diy opto endstop by gordon13	6,544	8	11/02/2013 07:43PM Last Post by slorite
Adding Adafruit Neopixel library to Marlin by callumburns	3,339	7	11/01/2013 08:58PM Last Post by callumburns
Gen 3 electronics help by Bill	593	6	10/30/2013 06:50AM Last Post by Traumflug
Changing steps per unit by bentomo	442	2	10/29/2013 02:07PM Last Post by jbernardis
Extruder shifts in the middle of a print by corben33	490	2	10/29/2013 02:06PM Last Post by jbernardis
Extruder Motor Not Working Properly by Flightless	907	1	10/29/2013 08:43AM Last Post by Flightless
marlin arduino compile error by homecore	1,110	3	10/28/2013 03:40PM Last Post by homecore
How can I download Repetier Firmware from arduino? by leadinglights	851	2	10/28/2013 08:24AM Last Post by Dust
Debugging tools? (Arduino Mega + Marlin) by chuyzoz	1,494	2	10/28/2013 08:18AM Last Post by Dust
Marlin Stepper Motors being strange by BillyP	991	1	10/25/2013 11:03PM Last Post by BillyP
Marlin V1 - 0.3mm increased print size by helmet	610	1	10/23/2013 03:29PM Last Post by helmet
Repetier timewarp?? by leadinglights	474	2	10/22/2013 03:55PM Last Post by leadinglights
Marlin on Rostock / RRD-LCD - preheat / auto extrude / stepper issues by hsiegel	811	1	10/22/2013 04:12AM Last Post by hsiegel
corexy with Marlin by Helmi	793	1	10/21/2013 05:12PM Last Post by Helmi
Z-Axis Homing difficulties by Morpheus	1,896	6	10/18/2013 04:16PM Last Post by Kayjay
Minitronics error: expected ',' or '...' before '&' token by guegueka1	1,128	2	10/08/2013 08:06AM Last Post by Traumflug
Prusa i3 Marlin settings problem? by JLudlow	3,518	2	10/05/2013 10:21PM Last Post by JLudlow
Compiling Repetier on BBB by daftscience	2,687	2	10/05/2013 03:20PM Last Post by flickerfly
Printer stops while job hasn't finished yet by deedee	779	2	10/03/2013 06:34PM Last Post by tleneel
Can't load Marlin firmware on Printrboard Rev D by saldor	842	2	10/03/2013 01:32AM Last Post by ianlee74
Marlin x-y Coordinates by nevertoolate	1,058	2	10/02/2013 05:49AM Last Post by Traumflug
Marlin steps per mm changes during print. by Pulseneko	887	4	09/30/2013 01:20AM Last Post by Pulseneko
Long response time to first command, then fine. by [email protected]	546	1	09/25/2013 10:35AM Last Post by [email protected]
Marlin PID performance by nophead	1,289	3	09/24/2013 11:12PM Last Post by Hardwarekiller

Page 28 of 42 Pages:

26 272829 30