Welcome! Log In Create A New Profile

Firmware - mainstream and related support

Page 27 of 42 Pages:

25 262728 29

Forum List New Topic RSS

	Views	Posts	Last Post
Marlin + Discount Smart Controller by T34r_A_Bit3	986	2	01/21/2014 02:15AM Last Post by stahlsau
Marlin and Multi Extruder Steps per Unit by spaceman	2,002	3	01/16/2014 04:53PM Last Post by jbernardis
Teacup, Thermistor, wrong temperature by WarriorDeluxe	1,290	2	01/16/2014 10:28AM Last Post by WarriorDeluxe
Marlin - setting up dual Y using E by azz00	904	2	01/05/2014 08:21AM Last Post by azz00
Different E steps/mm for each extruder by jbernardis	1,002	3	01/01/2014 09:51PM Last Post by jbernardis
Info Marlin documentation. by Ziko	536	2	01/01/2014 03:10PM Last Post by jbernardis
Axis moving in same direction for +/- Command by mtg5072	805	3	12/27/2013 03:41AM Last Post by Traumflug
Repetier-Firmware_0.83 - SPI.h by rudolf.gross	631	2	12/27/2013 03:37AM Last Post by Traumflug
MENDELMAX-MARLIN-MEGATRONICS V2-OPTOENDSTOP(AXES FAULT) by Levent	796	3	12/24/2013 03:25PM Last Post by rebecca.palmer
How to configurate a PTC100 tempsensor in Marlin by dune1982	580	1	12/23/2013 12:20PM Last Post by dune1982
Which way is UP Z axis limits etc by DonnyM	566	3	12/16/2013 01:17PM Last Post by DonnyM
Getting the configuration from the board by Borre	542	4	12/15/2013 05:12AM Last Post by Borre
Makerbot Clone Firmware Upload Failure by Theiso88	733	1	12/14/2013 08:33AM Last Post by Theiso88
z-axis stepper drivers and firmware by Briggs	746	4	12/09/2013 01:57PM Last Post by biszkopt80
problem in ramps by samy.loay	507	1	12/05/2013 06:55PM Last Post by samy.loay
Azteeg X3, Viki LCD and Repetier FW by Johnnymoto	1,686	4	12/05/2013 10:01AM Last Post by Johnnymoto
Can't connect with pronterface by kugel	15,679	9	12/05/2013 07:02AM Last Post by jalmasi
No x movement on marlin + sanguinalolu by hcker2000	535	2	12/04/2013 09:47AM Last Post by hcker2000
Problem compiling Marlin - claims variables are not defined by oskarbjo	925	7	12/02/2013 05:42AM Last Post by Traumflug
marlin help by freerpg	3,078	6	11/29/2013 04:51AM Last Post by freerpg
Printer Doesn't Recognize Y Endstop State Change by Rubidium86	1,827	9	11/28/2013 10:43PM Last Post by bigfilsing
cardreader.cpp:25: error 'DIOSDPOWER_PIN' was not declared by duckfriedrice	1,184	1	11/22/2013 10:44AM Last Post by duckfriedrice
Timelapse function to Marlin firmware, existing in sprinter by Farmer	1,073	1	11/22/2013 04:27AM Last Post by Farmer
Marlin + Ramps 1.4 LCD display gets meessy by dcohenb	2,060	7	11/21/2013 02:38AM Last Post by dcohenb
Azteeg X3 7 motors, slaved drives,etc setup ??? by DonnyM	1,506	5	11/19/2013 11:36PM Last Post by DonnyM
Marlin - Micro stepping Slowing down speed. by itscipher	938	2	11/19/2013 04:20AM Last Post by majic79
Marlin is doing short pauses between some moves by Phizinza	626	1	11/18/2013 02:00AM Last Post by Phizinza
stepper pulses duty cycle and optimization by yoavmil	2,973	3	11/15/2013 07:55AM Last Post by majic79
RTC for Marlin? by revwarguy	997	2	11/13/2013 08:13AM Last Post by majic79
Can't get Z axis moving in Marlin by Kayjay	2,288	2	11/13/2013 06:27AM Last Post by majic79

Page 27 of 42 Pages:

25 262728 29