Welcome! Log In Create A New Profile



Discuss any sort of mechanical stuff here: positioning systems, gears, extruding methods, etc. 
Subject Views Posts Last Post

"Practical" maximum size of cantilevered bed?

by The Mechanic
308 3 04/04/2016 09:59PM
Last Post by The Mechanic

Hot end ( nozzel) dragging across bed

by Jagtech
230 13 04/04/2016 12:38PM
Last Post by Jagtech

gt2 pully on leadscrew

by tenij000
216 2 04/04/2016 09:50AM
Last Post by george4657

How can I cut a lead screw in half?

by WalkerMaker
338 5 04/02/2016 05:23PM
Last Post by bdurbrow

Removing gears from steppers

by ksmith5135
10,268 24 04/02/2016 02:27AM
Last Post by Anonymous User

homing postion

by Novo
317 9 03/31/2016 12:27PM
Last Post by Novo

Why should I use a geared extruder?confused smiley

by WalkerMaker
402 3 03/30/2016 04:27PM
Last Post by the_digital_dentist

won't compile

by Jagtech
120 4 03/28/2016 10:53AM
Last Post by FA-MAS

Z axis not moving to next layer

by Jagtech
223 2 03/27/2016 12:47PM
Last Post by Jagtech

m5 nut motor side comes loose wen extruder goes down z axis p3steel

by tenij000
196 3 03/23/2016 09:33AM
Last Post by tenij000

Trouble with an MK8 extruder

by samuelk
247 2 03/22/2016 01:06AM
Last Post by samuelk

printing very thin filament in mini kossel Attachments

by inaali
195 2 03/20/2016 09:31AM
Last Post by stephenrc

New extruder calibration Attachments

by Albert MKossel
231 2 03/19/2016 08:26AM
Last Post by Albert MKossel

How can I start from scratch again?

by Jagtech
272 5 03/18/2016 08:49AM
Last Post by Jagtech

kinematics of bed plate adjustment

by rmlrn
285 6 03/15/2016 12:49PM
Last Post by Anonymous User

Best Value for SR20 Size Guide Rail

by makerparts
240 4 03/14/2016 06:19PM
Last Post by the_digital_dentist

Another question about H-Bot vs CoreXY

by MrDoctorDIV
5,944 6 03/14/2016 01:13PM
Last Post by WalkerMaker

New Z-Probe uses Load Cell Attachments

by palmerr23
678 9 03/13/2016 05:00PM
Last Post by palmerr23

mosfet bad ?

by Jagtech
122 2 03/12/2016 10:15PM
Last Post by Dust

sad smileyExtruder Keeps jamming

by WClampitt1
281 6 03/11/2016 02:51PM
Last Post by WClampitt1

Z axis - screw opposite linear support?

by rmlrn
248 5 03/11/2016 10:47AM
Last Post by the_digital_dentist


by the_digital_dentist
191 5 03/08/2016 04:16AM
Last Post by MechaBits

Which bed should i purchase for print under 100 microns ?

by conG
317 13 03/06/2016 06:07AM
Last Post by the_digital_dentist

Rail Support required

by makerparts
193 4 03/05/2016 07:50AM
Last Post by Anonymous User

What are the pros/cons of the various Z-Bed solutions?

by Draghi
746 14 03/05/2016 05:43AM
Last Post by the_digital_dentist

play in lead nut

by rmlrn
125 2 03/04/2016 04:20AM
Last Post by Anonymous User

Closed loop vs. stepper motors -advice sought

by jappiemike
1,040 24 03/04/2016 02:01AM
Last Post by dc42

Anyone Have a Moons Stepper Motor 17HD4063-01N datasheet?

by kidnamedtony
320 2 03/03/2016 04:06AM
Last Post by Anonymous User

Hybrid Polar-2d Delta Geometry - New design? Attachments

by jongscx
216 8 03/03/2016 12:45AM
Last Post by o_lampe

Small Nema17 for extruder/feeder?

by RichterK
263 4 03/02/2016 09:56AM
Last Post by dc42