Welcome! Log In Create A New Profile

Advanced

Controllers

Anything related to printer controllers not being Duet, RAMPS or Sanguinololu: microprocessors, motor and heater driver circuitry, gEDA/KiCAD issues, soldering tips, etc. 
Subject Views Posts Last Post

SMC and Firmware problems

by chuck
1,485 14 04/03/2009 10:40AM
Last Post by chuck

Extruder Won't Stop Extruding

by cpwebste
1,215 1 04/02/2009 05:23PM
Last Post by cpwebste

Gen. 2 Stepper Driver single sided

by flaex
3,518 14 03/31/2009 03:21AM
Last Post by johnrpm

H21LOB equivalent? Opto endstop with german parts...

by loonquawl
1,588 8 03/29/2009 09:04PM
Last Post by BodgeIt

Can you drive a 3.6V motor using PWM motor driver?

by DaveR
3,246 7 03/26/2009 03:30PM
Last Post by DaveR

Question about electronics kit at MakerStore

by Colecoman1982
1,185 5 03/25/2009 07:13PM
Last Post by Jmbjr2008

stepper motor driver v1.2 - one side down

by simonblackmore
1,965 19 03/21/2009 12:23PM
Last Post by freds

STMicroelectronics's L6208 Stepper Driver

by Snapai
1,900 2 03/20/2009 04:55AM
Last Post by VDX

PCB´s sold out!?

by Kolynos
1,013 3 03/18/2009 05:23AM
Last Post by Kolynos

Weak Stepper Motor Driver 1.2

by freds
1,217 3 03/17/2009 10:30PM
Last Post by freds

low temp fusable copper nanoparticles

by TheGuy
2,956 1 03/16/2009 03:01PM
Last Post by TheGuy

extruder wiring

by letsburn00
1,126 1 03/16/2009 06:31AM
Last Post by letsburn00

Stepper IDC connector.

by liav
980 2 03/14/2009 04:41AM
Last Post by Wade

PWM board lights are all on... Attachments

by jgilmore
1,312 11 03/13/2009 05:09AM
Last Post by nophead

Reprap2: Mendel circuit material

by Annirak
2,514 23 03/11/2009 08:17PM
Last Post by Annirak

Where to get the Sanguino Chip ?

by freds
1,160 5 03/11/2009 07:45PM
Last Post by Larry_Pfeffer

new kid

by krishnanhemanth
1,272 5 03/06/2009 01:39AM
Last Post by krishnanhemanth

Etching: Speeding up with induction burners?

by larsrc
1,367 12 03/04/2009 04:33AM
Last Post by nophead

Advertizing Not Aloud? ADMIN?

by cheeswiz
1,152 1 03/01/2009 04:37PM
Last Post by cheeswiz

Approx Cost of All Electronics?

by kodex
1,194 4 02/28/2009 11:15PM
Last Post by pingiscoolest

Modifying stepper driver circuit

by slisgrinder
1,939 13 02/28/2009 11:10PM
Last Post by pingiscoolest

Understanding the PDFs for the PCBs

by larsrc
1,174 5 02/27/2009 07:41PM
Last Post by jgilmore

error loading GCode_Interpreter

by pingiscoolest
1,048 8 02/26/2009 07:47PM
Last Post by pingiscoolest

compiling error(?) - arduino with gcode

by ralphthompson
1,306 2 02/26/2009 01:24PM
Last Post by ralphthompson

Need advice on lead-free soldering

by GeertB
2,314 9 02/25/2009 09:39PM
Last Post by pingiscoolest

nophead's vitreous enamel resistors

by fenn
1,349 8 02/24/2009 08:36PM
Last Post by Larry_Pfeffer

clogged through-holes

by Liav
974 3 02/22/2009 05:09AM
Last Post by nophead

Opto Endstop

by Bruno Martins
1,172 2 02/18/2009 07:45PM
Last Post by greenarrow

sanguino software & micros()

by bill rowe
977 7 02/17/2009 06:33PM
Last Post by kintel

Wiring questions

by reece.arnott
1,013 5 02/17/2009 01:21PM
Last Post by BodgeIt