Welcome! Log In Create A New Profile

Controllers

Anything related to printer controllers not being Duet, RAMPS or Sanguinololu: microprocessors, motor and heater driver circuitry, gEDA/KiCAD issues, soldering tips, etc.

Page 59 of 85 Pages:

57 585960 61

Forum List New Topic RSS

	Views	Posts	Last Post
Prolific 2303 USB to serial by hellobd	1,775	1	02/06/2011 12:25PM Last Post by hellobd
What kind of stepper for Mendel? by Ecir Hana	2,616	23	01/28/2011 06:26PM Last Post by calabris
gen 2 with sd card ? by karandex	879	1	01/27/2011 02:07PM Last Post by karandex
Type MOSFET in GEN3 Electronic from TechZone by AlexeyShokarev	1,148	4	01/27/2011 06:01AM Last Post by brupje
Multi Axis Bus topology by mango_make	1,258	3	01/22/2011 10:12AM Last Post by mango_make
Extruder controller h bridges kaput? by liav	796	2	01/19/2011 03:31AM Last Post by VDX
Extruder Controller 2.2 problem by Jeff B	1,805	9	01/14/2011 03:39AM Last Post by NoobMan
drv8811 and motherboard 1.2 by aarnis	1,422	3	01/12/2011 05:27AM Last Post by NoobMan
stepper motor only turning in one direction - was fine - pololu by AgeingHippy	8,082	7	01/11/2011 07:33AM Last Post by parag0n
Opto Endstop Problem by Milly	1,063	8	01/10/2011 02:10PM Last Post by Milly
suddenly I am getting waiterrors why? (SOLVED ) by AgeingHippy	963	7	01/09/2011 08:47PM Last Post by Triffid_Hunter
What actually does the extruder controller do? by AgeingHippy	1,474	9	01/09/2011 06:32PM Last Post by AgeingHippy
Oscilloscopes by davmj	1,512	14	01/09/2011 04:53AM Last Post by davmj
Z-Axis stepper motor controller testing. by Milly	1,460	3	01/04/2011 03:01PM Last Post by Milly
Troubleshooting V1.2 Motherboard by mr.marmot	787	7	12/31/2010 11:15PM Last Post by Grogyan
Motherboard + USBTinyISP: avrdude: initialization failed, rc=-1 by sicarius	4,582	3	12/29/2010 07:57PM Last Post by NoobMan
Tech Zone Electronics, Extruder Motor stops when Heater reachs a certain Temperature by tayeb	891	3	12/24/2010 09:18AM Last Post by tayeb
Prototype Stepper Motor Shield Fabricated by thereza	2,034	13	12/17/2010 08:06PM Last Post by BodgeIt
challenge : Protect stepper drivers from getting fried by AgeingHippy	3,283	19	12/15/2010 08:24PM Last Post by NoobMan
attaching heat sink to pololu chip - with what? by AgeingHippy	5,170	15	12/13/2010 08:47PM Last Post by NoobMan
pololu stepper driver is dead - do I need to pullup ENABLE? by AgeingHippy	1,715	10	12/13/2010 05:51PM Last Post by Triffid_Hunter
Replacement components by Mihara	915	6	12/13/2010 04:02AM Last Post by Bart Meijer
capabilities of the components used by danielramos	770	1	12/12/2010 04:16PM Last Post by danielramos
Extruder controller missing component? by Milly	940	6	12/09/2010 06:08PM Last Post by Milly
Testing Gen3 Motherboad, help please! by Milly	841	3	12/09/2010 09:10AM Last Post by Milly
A3977 3.3v board tuning / motor math by NoobMan	1,944	1	12/03/2010 07:33AM Last Post by NoobMan
Does anyone in Canada sell the USB to TTL cable? by Adam.m.Nelson	2,055	13	12/03/2010 03:41AM Last Post by VDX
ReplicatorG/RepRap Motherboard (MakerBot) Tubing Cutter by wireframe	2,385	4	12/02/2010 01:49PM Last Post by wireframe
USB TTL cable pins by mattuwattu	6,072	8	12/02/2010 01:48PM Last Post by Jamal
Post-mortem help requested by chupacabra	844	7	12/01/2010 12:37PM Last Post by parag0n

Page 59 of 85 Pages:

57 585960 61