Welcome! Log In Create A New Profile

Advanced

Controllers

Anything related to printer controllers not being Duet, RAMPS or Sanguinololu: microprocessors, motor and heater driver circuitry, gEDA/KiCAD issues, soldering tips, etc. 
Subject Views Posts Last Post

Are my DRV8825's backwards?

by kd6hq
438 7 01/22/2017 06:20PM
Last Post by kd6hq

Melzi overheat problem Attachments

by sprue
229 5 01/15/2017 09:26AM
Last Post by dc42

Megatronics v3 (DRV8825) stepper won't move anymore

by ultraflash
1,013 7 01/11/2017 05:20PM
Last Post by Govahnator

Rumba with ATX power supply problem

by geekololo
757 2 01/11/2017 03:51PM
Last Post by boteci9393

New TFT control panel for 3D printers

by dc42
5,836 19 01/10/2017 10:57PM
Last Post by dc42

Which controller for an i3 based machine?

by Twmaster
254 4 01/09/2017 10:35AM
Last Post by Twmaster

How to use the Rumba SD Reader directly on Arduino?

by kimented_
289 1 01/06/2017 11:41AM
Last Post by kimented_

When using a RUMBA controller what pin is used for SDSS ?

by kd6hq
281 3 01/04/2017 04:14AM
Last Post by kd6hq

MKS TFT32 - Getting Feedback from the board?

by xelad
244 1 01/04/2017 02:56AM
Last Post by xelad

RADDs board & remapping hotend Heaters to extra Fans

by amellors
299 1 12/25/2016 03:48PM
Last Post by amellors

Heated Bed controled with arduino relay modul and AUX Pin (D1)

by bob_dit
718 7 12/15/2016 02:53PM
Last Post by dc42

TFT28 or TFT32 touch screen on a Radds Attachments

by Couture619
768 2 12/12/2016 10:21PM
Last Post by KDog

ATX supply to power RPi / RAMPS / OctoPi

by milt
4,049 17 12/05/2016 10:34AM
Last Post by yanickr1973

Expanding the RUMBA to a fourth extruder Attachments

by Billi3
651 3 12/03/2016 11:46AM
Last Post by nmvet

ANDCIV CM3G3 Third-generation Board

by Widget
1,818 10 11/27/2016 02:13AM
Last Post by grimlok2000

MKS TFT28 english manual?

by yanickr1973
347 3 11/26/2016 01:20AM
Last Post by Bobyni

I need some advice on path to follow for a Diamond hot end conversion.

by kd6hq
274 4 11/23/2016 05:38AM
Last Post by kd6hq

Help: MKS SBASE 1.3 Smoothieware Delta setup Attachments

by scarecrow2k6
1,028 4 11/22/2016 09:41PM
Last Post by chris33

GT Smart 20*4 Controller + GT2560 nonstop beeping

by shaolin30
248 2 11/20/2016 06:48PM
Last Post by shaolin30

Thermistors not worked properly

by Agasfer
250 4 11/20/2016 11:48AM
Last Post by Agasfer

fried mega 2560?

by jotus
244 1 11/19/2016 11:54AM
Last Post by jotus

melzi v2 board

by Roger123D
285 2 11/19/2016 05:08AM
Last Post by o_lampe

Beaglebone Machinekit Build Advice

by turbo329is
391 4 11/17/2016 06:35PM
Last Post by turbo329is

RADDS SD card read error

by edwell
658 6 11/16/2016 08:03AM
Last Post by deaconfrost

Rumba ABL servo issues Attachments

by Felice
276 2 11/05/2016 02:45AM
Last Post by Felice

Melzi 2 Esteps calibration - no existing figure to recalculate from??

by Mr Joshua
249 8 11/03/2016 05:45PM
Last Post by Mr Joshua

(SOLVED) Biqu RUMBA board and Heatbed Attachments

by kimented_
366 1 11/01/2016 03:51AM
Last Post by kimented_

Arduino Due + RAMPS-FD, PS_ON pin goes high on reset problem.

by ld
462 3 10/29/2016 07:54AM
Last Post by ld

BIQU MKS SBASE Help Attachments

by mildot
394 4 10/24/2016 09:36AM
Last Post by chris33

New ARM Controller Board   (Pages: 1 2)

by JustAnotherOne
3,604 31 10/20/2016 03:36PM
Last Post by Rlewisrlou666