Welcome! Log In Create A New Profile

Advanced

Controllers

Anything related to printer controllers not being Duet, RAMPS or Sanguinololu: microprocessors, motor and heater driver circuitry, gEDA/KiCAD issues, soldering tips, etc. 
Subject Views Posts Last Post

Anyone here using the BeagleBone (Black) to control their 3D printer?

by marcosscriven
5,347 8 07/15/2014 10:46PM
Last Post by esponda

Beeper and RUMBA board

by kimented_
446 1 07/15/2014 06:44AM
Last Post by kimented_

Solution to endstop cross talk?

by TheSerialHobbyist
3,199 17 07/14/2014 02:14PM
Last Post by NoobMan

New build / Rambo problem

by charlieRC
553 4 07/14/2014 01:11PM
Last Post by charlieRC

24V to 12V Heater

by GowthamJGR
4,492 10 07/08/2014 06:56AM
Last Post by Traumflug

3A stepper motor driver

by TheDeadLives
1,184 6 07/07/2014 03:39PM
Last Post by TheDeadLives

Help replace dead hotend heater (Ohm's Law and Rated Wattage)

by MRGiacalone2005
3,087 11 07/04/2014 01:08PM
Last Post by MRGiacalone2005

Replacing Melzi stepper drivers?

by jakobnator
1,289 3 07/03/2014 09:53PM
Last Post by jakobnator

Power Supply Problem

by timmit99
605 6 07/02/2014 10:41PM
Last Post by timmit99

2 x 100k Thermistors

by Stabilize
417 2 07/01/2014 01:30AM
Last Post by waitaki

Chosing resistors for heating

by letsburn00
8,669 11 06/29/2014 11:52PM
Last Post by MRGiacalone2005

Ramps 1.4 COM Connection Issue: HELP!

by Janski
441 1 06/27/2014 02:50PM
Last Post by Janski

Help choosing a control board

by TheSerialHobbyist
1,058 9 06/26/2014 07:09PM
Last Post by Anonymous User

Heat Bet Voltage Question: smiling smileyRamps1.4

by Janski
531 7 06/26/2014 02:33PM
Last Post by Janski

Using the PS_ON

by Rigor_M
782 1 06/25/2014 09:42AM
Last Post by Rigor_M

a diver must get hot and not working

by amira
442 2 06/24/2014 01:02AM
Last Post by Cefiar

Brownout reset general cause?

by sungod3k
1,172 12 06/23/2014 10:35PM
Last Post by sungod3k

Help Wiring Large (12"x12") Heatbed Through Relay or MOSFET

by TheSerialHobbyist
4,415 23 06/23/2014 10:21AM
Last Post by TheSerialHobbyist

Servo wobbling, basic electronics question inside .. Help needed

by Yellobello
1,416 14 06/23/2014 09:01AM
Last Post by Yellobello

Looking to upgrade My heatbed MK2A-ALU 3mm Heatbed- Has anyone used? Recommend?

by bladez
1,145 10 06/21/2014 12:33AM
Last Post by wmtdanimal

BAM&DICE an new RAMPS compatible electronics

by Domonoky
860 12 06/18/2014 05:14PM
Last Post by WZ9V

Incorrect information on Thermistor wiki

by genelmx
653 7 06/18/2014 05:47AM
Last Post by Traumflug

Can Motors with Different AMP Draws be Mixed in One Machine?

by Garry Bartsch
694 5 06/15/2014 06:29PM
Last Post by Garry Bartsch

avrdude: verification error and other weird behavior

by sungod3k
1,424 20 06/14/2014 12:32PM
Last Post by NoobMan

Adding A Mains Power Switch

by BradStaff
383 2 06/14/2014 08:19AM
Last Post by vreihen

Tricolor Melzi Boards communication errors

by chickenchuck040
481 1 06/13/2014 12:52PM
Last Post by chickenchuck040

My little ARM board Attachments

by Mallgan.O
2,226 24 06/12/2014 06:43AM
Last Post by Mallgan.O

Megatronics Reset

by mojohand
1,028 3 06/12/2014 05:58AM
Last Post by vreihen

Downclocking?!

by sungod3k
653 5 06/12/2014 04:52AM
Last Post by Traumflug

Glass inspection

by Laserglass
484 2 06/10/2014 03:54PM
Last Post by VDX