Welcome! Log In Create A New Profile

Advanced

Controllers

Anything related to printer controllers not being Duet, RAMPS or Sanguinololu: microprocessors, motor and heater driver circuitry, gEDA/KiCAD issues, soldering tips, etc. 
Subject Views Posts Last Post

MKS BASE - procedure to diagnose / swap bad mosfet

by david784
216 4 09/11/2017 01:21PM
Last Post by david784

Selecting the right electronics for my project

by yala
416 17 09/05/2017 11:51PM
Last Post by dc42

RUMBA board or Smart Controller LCD 'idiosyncrasy?"

by TJM3D
314 4 09/04/2017 12:47AM
Last Post by o_lampe

Prusa extruder mux

by Dust
279 3 08/22/2017 09:10AM
Last Post by dc42

Dumb question about RADDS hall sensor

by bryanbdp
189 2 08/21/2017 12:14AM
Last Post by o_lampe

How to set up microstep on StepStick using A4988 ?

by trietdao95
203 3 08/16/2017 05:15PM
Last Post by Dust

tronxy melzi 2 boards??

by munchit1
299 5 08/15/2017 07:21AM
Last Post by munchit1

What's the easiest way to do this?

by Desertboy
213 2 08/15/2017 12:58AM
Last Post by o_lampe

The probably cheapest and most modular 32bit solution.

by JustAnotherOne
586 7 08/12/2017 12:00PM
Last Post by JustAnotherOne

Sinaptec DIY build Attachments

by Dominium
322 3 08/05/2017 01:35AM
Last Post by Dominium

Megatronics V2- Inverted end stop damage IC2 Attachments

by MRGiacalone2005
1,008 11 08/01/2017 08:20PM
Last Post by Dust

Controlling Solenoid Valve signal

by JoshuahMG
220 4 07/28/2017 03:57PM
Last Post by VDX

Hot End Temperature Not Reading Accurately Attachments

by redhatman
8,593 12 07/22/2017 02:48PM
Last Post by gbond

[dumb question] Turn on fans at a certain current?

by pugzor
222 6 07/19/2017 10:32PM
Last Post by o_lampe

Rambo Mini issue

by sTon
311 7 07/14/2017 04:28AM
Last Post by sTon

AZSMZ 12864 LCD + ESP8266 (ESP3D) Attachments

by cxandy
407 1 07/12/2017 07:13PM
Last Post by cxandy

is RADDS not open source?

by ekaggrat
1,329 20 07/12/2017 04:04PM
Last Post by VDX

Printer not reading SD card / bad connection between controller and LCD screen

by Maggie_at_OESH
206 2 07/11/2017 10:49AM
Last Post by Maggie_at_OESH

Rambo 1.3 board extruder motor stutter

by kutch2001
1,261 12 07/06/2017 08:45AM
Last Post by thomaaa

3DTouch and reprap firmware

by BramV
290 2 07/01/2017 11:27AM
Last Post by dc42

newbie setting up the MKS Sbase...confused smiley

by jetboy1
324 5 06/28/2017 02:21AM
Last Post by jetboy1

BL Touch and BIQU MKS-BASE V1.5 Plate Controller Board Attachments

by panadar
707 2 06/28/2017 02:14AM
Last Post by Kruemel33

PCB manufacturing with a LCD layermask, possible?

by ElectricMucus
2,363 7 06/21/2017 11:07AM
Last Post by altnelu

Controller LCD contrast issue   (Pages: 1 2)

by drhender
21,303 42 06/21/2017 06:18AM
Last Post by carlonb

3D Touch z-probe and RADDS

by BramV
371 5 06/19/2017 11:33AM
Last Post by BramV

Z max endstop issues

by bread_bird
249 5 06/18/2017 11:55AM
Last Post by bread_bird

X Axis homing in wrong direction after hot end upgrade

by fullHundo
223 1 06/17/2017 11:59PM
Last Post by fullHundo

Make a Drive By Wire Circuit Control System

by display
236 3 06/16/2017 11:09PM
Last Post by o_lampe

how to upload firmware to melzi v2 board? Attachments

by kkwong1951
2,452 9 06/16/2017 12:08AM
Last Post by DenisSh

Image 2 LCD

by 762x51
364 2 06/12/2017 06:29AM
Last Post by 762x51