Welcome! Log In Create A New Profile

Advanced

Controllers

Anything related to printer controllers not being Duet, RAMPS or Sanguinololu: microprocessors, motor and heater driver circuitry, gEDA/KiCAD issues, soldering tips, etc. 
Subject Views Posts Last Post

lerdge board 32 bits   (Pages: 1 2 3 4)

by titeuf007
3,220 109 08/17/2017 04:50AM
Last Post by maralb

How to set up microstep on StepStick using A4988 ?

by trietdao95
46 3 08/16/2017 05:15PM
Last Post by Dust

tronxy melzi 2 boards??

by munchit1
111 5 08/15/2017 07:21AM
Last Post by munchit1

What's the easiest way to do this?

by Desertboy
85 2 08/15/2017 12:58AM
Last Post by o_lampe

The probably cheapest and most modular 32bit solution.

by JustAnotherOne
253 7 08/12/2017 12:00PM
Last Post by JustAnotherOne

New MKS SBASE Smoothieware-compatible board from China   (Pages: 1 ... 23 24 25)

by vreihen
88,752 738 08/11/2017 06:43AM
Last Post by edvard051

Sinaptec DIY build Attachments

by Dominium
138 3 08/05/2017 01:35AM
Last Post by Dominium

New 32 bits ARM MKS Robin with TFT??   (Pages: 1 2 3)

by Bobyni
8,929 66 08/05/2017 12:43AM
Last Post by edvard051

DIY Tiny OLED I2C full graphics controller Attachments   (Pages: 1 2 3 4 5)

by enif
23,062 147 08/02/2017 07:28AM
Last Post by Twmaster

Megatronics V2- Inverted end stop damage IC2 Attachments

by MRGiacalone2005
933 11 08/01/2017 08:20PM
Last Post by Dust

Controlling Solenoid Valve signal

by JoshuahMG
96 4 07/28/2017 03:57PM
Last Post by VDX

Hot End Temperature Not Reading Accurately Attachments

by redhatman
7,203 12 07/22/2017 02:48PM
Last Post by gbond

[dumb question] Turn on fans at a certain current?

by pugzor
112 6 07/19/2017 10:32PM
Last Post by o_lampe

RADDS work now stable with RepRap Firmware   (Pages: 1 ... 24 25 26)

by angelo
21,536 759 07/18/2017 01:44PM
Last Post by dc42

Rambo Mini issue

by sTon
193 7 07/14/2017 04:28AM
Last Post by sTon

AZSMZ 12864 LCD + ESP8266 (ESP3D) Attachments

by cxandy
163 1 07/12/2017 07:13PM
Last Post by cxandy

is RADDS not open source?

by ekaggrat
1,156 20 07/12/2017 04:04PM
Last Post by VDX

Printer not reading SD card / bad connection between controller and LCD screen

by Maggie_at_OESH
97 2 07/11/2017 10:49AM
Last Post by Maggie_at_OESH

Rambo 1.3 board extruder motor stutter

by kutch2001
1,103 12 07/06/2017 08:45AM
Last Post by thomaaa

3DTouch and reprap firmware

by BramV
167 2 07/01/2017 11:27AM
Last Post by dc42

newbie setting up the MKS Sbase...confused smiley

by jetboy1
180 5 06/28/2017 02:21AM
Last Post by jetboy1

BL Touch and BIQU MKS-BASE V1.5 Plate Controller Board Attachments

by panadar
248 2 06/28/2017 02:14AM
Last Post by Kruemel33

PCB manufacturing with a LCD layermask, possible?

by ElectricMucus
2,245 7 06/21/2017 11:07AM
Last Post by altnelu

Controller LCD contrast issue   (Pages: 1 2)

by drhender
19,297 42 06/21/2017 06:18AM
Last Post by carlonb

3D Touch z-probe and RADDS

by BramV
170 5 06/19/2017 11:33AM
Last Post by BramV

Z max endstop issues

by bread_bird
185 5 06/18/2017 11:55AM
Last Post by bread_bird

X Axis homing in wrong direction after hot end upgrade

by fullHundo
133 1 06/17/2017 11:59PM
Last Post by fullHundo

Make a Drive By Wire Circuit Control System

by display
170 3 06/16/2017 11:09PM
Last Post by o_lampe

how to upload firmware to melzi v2 board? Attachments

by kkwong1951
1,441 9 06/16/2017 12:08AM
Last Post by DenisSh

Image 2 LCD

by 762x51
238 2 06/12/2017 06:29AM
Last Post by 762x51