Welcome! Log In Create A New Profile

Advanced

RepRap en Español

Subject Views Posts Last Post

Ayuda!, Problema con extrusor Attachments

by felgro
39 1 04/14/2014 03:10PM
Last Post by felgro

Busco las piezas imprimibles

by darbiter
41 1 04/13/2014 09:24AM
Last Post by darbiter

como configurar el ventilador?

by jhz1983
163 3 04/10/2014 06:34AM
Last Post by maltasev

No me detecta estrusor ni cama caliente

by chupis
102 2 04/10/2014 06:30AM
Last Post by maltasev

Espesor chapa Prusa Leonardo (Prusa Steel).

by GAZ082
71 1 04/09/2014 06:56PM
Last Post by GAZ082

[SOLUCIONADO] ¿Alguién me puede imprimir y vender los BELT guide para 623ZZ?

by eperezsa
76 2 04/09/2014 01:38PM
Last Post by eperezsa

LOS MOTORES NO SE MUEVEN NI SUENAN

by mmusicoc
65 3 04/07/2014 02:12PM
Last Post by mmusicoc

problemas motores como ajustar igual que en texapu_rx como si usara pwm

by alexrlopez86
72 1 04/06/2014 02:34PM
Last Post by alexrlopez86

Duda de novato

by JbeltranCW
86 2 04/06/2014 01:39PM
Last Post by Plunket

Ayuda, motores vibran, no calienta ni cama caliente ni extrusor

by alka7a
114 2 04/05/2014 05:44AM
Last Post by misan

Ayuda: Imposible mover motores Attachments

by jessmann
1,129 11 04/05/2014 05:43AM
Last Post by misan

Dónde comprar termistores

by paxkuali
134 5 04/01/2014 06:45AM
Last Post by paxkuali

PROBLEMAS EN IMPRESION Attachments

by olascoaga29
135 2 03/27/2014 05:45AM
Last Post by iniciativas3d

Problema, Solo se mueven los motores en un sentido.

by chupis
205 9 03/19/2014 12:02AM
Last Post by coti

Soporte al imprimir ¿como funciona? consejos/sugerencias

by thingmaker
584 6 03/18/2014 11:43PM
Last Post by massieu11

Proyecto final, cuál construir?

by Pablo_ind
155 4 03/18/2014 03:48AM
Last Post by misan

Como imprimir estas Piezas?

by rama007
678 6 03/17/2014 07:53PM
Last Post by massieu11

Consulta sobre eje z y fin de carrera

by martinlt
133 2 03/16/2014 10:02AM
Last Post by Plunket

DOBLE EXTRUSOR

by ignpliolm
133 1 03/14/2014 07:23PM
Last Post by ignpliolm

pregunta eje Z movimiento

by Juan
175 3 03/09/2014 05:12PM
Last Post by Juan

HEACENT REPRAP PRUSA 3DP02

by DoctorTracker
226 5 03/08/2014 03:30AM
Last Post by DoctorTracker

Kit Prusa i3 completo 425€ y mucho más en CREATEC 3D hot smiley

by jrdetoro
202 1 03/03/2014 11:42PM
Last Post by jrdetoro

RepRap en Uruguay   (Pages: 1 2)

by kevin
3,351 39 03/03/2014 08:55AM
Last Post by CaptainObvious

Mover Bandeja en eje z

by carpincho78
125 1 02/26/2014 06:22PM
Last Post by carpincho78

VIBRACION Y RUIDO

by olascoaga29
142 4 02/26/2014 03:32PM
Last Post by olascoaga29

Configuración

by artu_guti
220 3 02/25/2014 05:54AM
Last Post by lokus77

primer kit prusa mendel i3 INDECISO!

by monbesugo
404 10 02/25/2014 05:21AM
Last Post by lokus77

Impresora de circuitos impresos con un pickup Blue-Ray

by Mecatronic
300 3 02/24/2014 03:35PM
Last Post by miguel_angel

Problema extrusion directa

by aj.moreno
318 8 02/24/2014 10:07AM
Last Post by miguel_angel

metiendo el programa a la tarjeta de arduino

by Juan
258 7 02/23/2014 03:37PM
Last Post by arquitron