Welcome! Log In Create A New Profile

Advanced

General

General discussions. For specific printers / electronics / fabrication methods / softwares, please see other sections. 
Subject Views Posts Last Post

Thermal Runaway error

by rizulthkr
260 2 05/03/2017 04:09AM
Last Post by Srek

Arduino Voltage regulator gets hot when I connect a raspberry Pi to it.

by Nadim
285 4 05/03/2017 12:53AM
Last Post by DjDemonD

Double sided/passthrough bowden connector?

by clearlynotstefan
304 4 05/02/2017 03:54AM
Last Post by Ed would

External Mosfet boards actually quite good! Attachments

by DjDemonD
1,268 29 05/01/2017 04:12PM
Last Post by DjDemonD

Filament diameter compensation Attachments

by RGN01
323 16 05/01/2017 06:23AM
Last Post by paulhurleyuk

Pololu geared DC motor 30g prototype extruder Attachments   (Pages: 1 ... 7 8 9)

by ipcalit
8,395 254 04/30/2017 05:16PM
Last Post by roboprint

Extruder stepper makes buzzing noise on my I3

by Nadim
218 2 04/29/2017 02:29PM
Last Post by DjDemonD

problema marlin con endstop

by Vittorio1234
220 2 04/29/2017 08:04AM
Last Post by obewan

High performance motor controllers   (Pages: 1 2)

by madcowswe
2,296 44 04/28/2017 06:58PM
Last Post by madcowswe

Bloomin Mental

by MechaBits
623 9 04/28/2017 01:23PM
Last Post by MechaBits

Endstop asse X

by Ripi
214 1 04/28/2017 08:11AM
Last Post by Ripi

DIY 400x400x200 printer, choice question / doubt   (Pages: 1 2)

by HugoW
1,125 38 04/28/2017 05:29AM
Last Post by newbob

3D Electroplating?

by sanman
6,088 23 04/28/2017 04:42AM
Last Post by eklavya_1

Turn you 3D Printer into a Rail Gun Attachments   (Pages: 1 2)

by MechaBits
1,624 37 04/28/2017 03:54AM
Last Post by MechaBits

Help With Print Quality Attachments

by 1lug1998
327 3 04/27/2017 05:25PM
Last Post by drgrs

Can TMC2100 drive Nema17 stepper ?

by DaveOB
245 3 04/27/2017 03:51PM
Last Post by DjDemonD

Extruder seems to stop outputting randomly

by Zeoic
322 11 04/27/2017 02:04PM
Last Post by drgrs

Endstops not working after firmware upgrade

by prof braino
577 7 04/27/2017 05:42AM
Last Post by parto

Micromake C1 Prusa i3 H-bot with x and z axis Attachments

by micromake1
940 10 04/27/2017 03:07AM
Last Post by Medelis

PID autotune failed! Bad extruder number

by rizulthkr
291 8 04/27/2017 02:21AM
Last Post by Srek

How to wire a z axis brake on my build ?

by paboman
193 4 04/25/2017 09:57AM
Last Post by Srek

Can any slicer vary layer height?

by newbob
375 8 04/24/2017 07:30PM
Last Post by scottybfg

Can stall detection at stepper driver level be used to account for backlash in a geared system?

by realthor
247 4 04/24/2017 11:40AM
Last Post by 691175002

Need programming help for laser engraver - based on stock marlin 1.1.0-RC8 and RAMPS 1.4

by huhubibi
255 2 04/24/2017 08:01AM
Last Post by huhubibi

300x300 ALU heatbed wiring Attachments

by tgmorris99
419 22 04/22/2017 04:10PM
Last Post by Origamib

Understanding long Lead Screws

by shortyski13
484 19 04/22/2017 02:15PM
Last Post by the_digital_dentist

Better slicer/controller

by newbob
298 9 04/21/2017 03:13PM
Last Post by newbob

Automatic Manual bed leveling needed

by newbob
525 22 04/21/2017 02:45PM
Last Post by DjDemonD

Proximity Sensor Wiring Incorrect

by morris4019
240 5 04/21/2017 09:11AM
Last Post by morris4019

At 1% of FAN percentage on LCD, My controller FAN is getting ON at FULL speed.....Help

by ManiPi
230 1 04/21/2017 08:14AM
Last Post by ManiPi