Subject		Views	Posts	Last Post
	RepRap Stepper Extruder Problem by sihtamsivart	1,474	11	11/29/2010 10:09PM Last Post by sihtamsivart
	Robitics by mattuwattu	801	5	11/29/2010 09:22PM Last Post by Anthong Redbeard
	Oozing during temperature change causes poor deposition at start of layer by gklyne	983	3	11/28/2010 03:18PM Last Post by Vollnormal
	RapMan(Version 3.1) 3D Printer by tommy	1,064	2	11/28/2010 12:07AM Last Post by Duaner
	Reprap extruder nozzles by Phobia1	1,019	2	11/26/2010 07:57PM Last Post by RepRich
	where to start by kenny	804	2	11/26/2010 06:32AM Last Post by SebastienBailard
	Mendel X Axis Carriage - too much clearance from bearings to rod by m100	1,193	5	11/25/2010 12:09PM Last Post by m100
	My motors shake by eranglr	753	1	11/24/2010 05:47PM Last Post by eranglr
	Can a single person with no hands-on experience do a reprap? by bugler	1,055	11	11/24/2010 04:24PM Last Post by RepRich
	Bioplastic movie by murrayd	954	6	11/23/2010 02:07AM Last Post by dissidence
	Motor shield for extruder stepper by eranglr	1,168	14	11/22/2010 07:01PM Last Post by Cefiar
	ReprapKit ABS quality by AgeingHippy	829	1	11/22/2010 08:26AM Last Post by AgeingHippy
	3d Model of Constructed Mendel by FizzRap	1,285	6	11/21/2010 05:31AM Last Post by TomCeeMe
	ABS on Non-heated bed? by An Original Name	890	2	11/20/2010 08:20PM Last Post by fdavies
	ABS and PLA Testers wanted by RepRap Central	1,422	10	11/20/2010 03:16PM Last Post by Greg Frost
	3D fabbers: don't let the DMCA stifle an innovative future by Capo	1,243	14	11/20/2010 08:28AM Last Post by trebuchet03
	Ditch our firmware, run EMC2's RT code on our micros instead? by jgilmore	1,010	5	11/19/2010 08:18PM Last Post by jgilmore
	Wades Extruder by Magnum	1,021	7	11/19/2010 05:34PM Last Post by Magnum
	Non-permanent Rigging of a Computer PSU for RepRap (with pictures!) by An Original Name	1,765	6	11/19/2010 07:32AM Last Post by Nudel
	SAE all-metal hot end, how to taper the melt zone? by jgilmore	1,112	3	11/19/2010 12:50AM Last Post by Bruce
	Which plastic to start with? by AgeingHippy	915	4	11/18/2010 11:16AM Last Post by TomCeeMe
	Z Axis not moving (Resolved) by bbriggstkd	2,577	14	11/18/2010 07:33AM Last Post by bbriggstkd
	greycode idea by loqk	806	2	11/18/2010 05:57AM Last Post by SebastienBailard
	Stepper Motors by Magnum	1,391	19	11/18/2010 12:17AM Last Post by Magnum
	Incremental copies and tolerences? by ablainey	1,033	4	11/17/2010 06:52AM Last Post by murrayd
	New to RepRap by Magnum	1,435	24	11/16/2010 08:47PM Last Post by Magnum
	new website I found, prototypetoday.com by TimRuffner	997	6	11/16/2010 06:21PM Last Post by SebastienBailard
	Frostruder by carpenma	2,216	6	11/13/2010 07:50PM Last Post by hintss
	3D Scanner from kinect (microsoft) by bobt	1,447	3	11/12/2010 11:55PM Last Post by dissidence
	Huxley bearing count by Auzze			This topic has been moved.