Subject		Views	Posts	Last Post
	Arcol Hot End and Licenses   (Pages: 1 2 3 4) by draeician	4,675	94	04/28/2011 03:11AM Last Post by SebastienBailard
	Prusa Z axis coupling reliability by owism8	2,839	12	04/28/2011 02:53AM Last Post by Greg Frost
	NiChrome input voltage/ amperage (Prusa) by Hobbes20xx	2,157	10	04/27/2011 09:26PM Last Post by brnrd
	Master Thesis - Your help is needed.. by MichaelT	944	6	04/27/2011 09:10PM Last Post by Tony
	Heat insulation for extruder by ketil	1,092	2	04/27/2011 08:44PM Last Post by Cefiar
	Larger build envelope by alelazz	840	4	04/27/2011 04:58PM Last Post by jcabrer
	Thick Sheet Thickness? by MarkMills	738	7	04/26/2011 11:27PM Last Post by Greg Frost
	Extruder not heating by rtdesign	1,053	4	04/26/2011 12:47PM Last Post by jcabrer
	How to print out a Monolithic board? by owism8	1,015	2	04/25/2011 11:05PM Last Post by jamesdanielv
	Copper tape circit boards(experiment by ronanwarrior	7,583	14	04/25/2011 06:07PM Last Post by jamesdanielv
	Dual-head, plastic/wax printer, for voids and support? by Dale Mahalko	2,496	9	04/25/2011 05:46PM Last Post by MattMoses
	Electronic Kits, Who's are the best?? by tony woollacott	1,248	16	04/25/2011 11:19AM Last Post by owism8
	Rescue Tape by owism8	1,028	11	04/25/2011 07:52AM Last Post by owism8
	lasercut z ais motor pully slipping by anode505	1,475	7	04/23/2011 02:26PM Last Post by epengr
	self-replicating factories? by Marcus	1,495	6	04/22/2011 02:25PM Last Post by jgilmore
	Tough X-axis? by ketil	2,242	20	04/22/2011 12:39PM Last Post by owism8
	Electronics Club by Nicco	719	2	04/22/2011 04:14AM Last Post by SebastienBailard
	flipped/mirroed prints by Rooski	784	2	04/21/2011 11:57PM Last Post by Rooski
	Arcol.hu Hotend and Prusa Compatibility. by schulz	1,312	3	04/21/2011 03:21PM Last Post by Anthong Redbeard
	X Carraige dimensions available?? by AgeingHippy	934	4	04/21/2011 04:25AM Last Post by jamesdanielv
	Reprap as vinyl cutter ? by oh6kft	1,906	7	04/21/2011 02:01AM Last Post by jamesdanielv
	How Smooth do smooth rods have to be on Prusa? by schulz	2,454	17	04/20/2011 07:20AM Last Post by schulz
	Tinkercad, online 3d modelling by mlagana	2,180	2	04/20/2011 06:31AM Last Post by garyhodgson
	Rock tumbler? by Adrian	1,124	6	04/19/2011 12:32AM Last Post by brnrd
	use of codec to speed up gcode operations by jamesdanielv	1,383	27	04/18/2011 11:15PM Last Post by jamesdanielv
	Skeinforge 40 and sparse infill by ketil	1,765	6	04/17/2011 08:59PM Last Post by brnrd
	Reference Material - Books-etc Recomendations please etc by vizion	937	1	04/16/2011 01:32PM Last Post by vizion
	Getting extruder to extrude by HereIgoAgain	1,286	12	04/16/2011 01:06PM Last Post by brnrd
	New Reprapper (electronics question) by Hobbes20xx	1,160	6	04/16/2011 01:15AM Last Post by mlagana
	Scrape Nozzle Head before print? by MrJohn	951	2	04/14/2011 07:38PM Last Post by brnrd