Subject		Views	Posts	Last Post
	buildatron by dissidence	1,007	9	01/30/2012 09:01PM Last Post by NelsonRap
	BotMill has the Fastest Shipping Times Around!   (Pages: 1 2) by BotMill	2,042	31	01/30/2012 03:59PM Last Post by botmillshaan
	My first reprap is complete! MendelMax... by PastaRocket848	1,698	11	01/30/2012 02:57PM Last Post by nophead
	Did I get the wrong stepper motors? by jd1828	2,322	5	01/29/2012 07:06PM Last Post by ambiguousphoton
	Why is ABS worse for press fit parts? by jsadusk	2,918	6	01/29/2012 06:56PM Last Post by Andrew Diehl
	Z-axis spiral coupler by Skypuppet	1,415	8	01/29/2012 01:32PM Last Post by Skypuppet
	Why am I getting this error with skeinforge on repetier host? by sagtf1	976	3	01/29/2012 11:09AM Last Post by 0kumy0
	Problem with generating Gcode for STL by wikisi	1,036	7	01/28/2012 10:54AM Last Post by wikisi
	power supply for a mg prusa by glrra19	872	2	01/28/2012 06:11AM Last Post by misan
	less support material by glrra19	798	4	01/28/2012 04:48AM Last Post by glrra19
	3D Systems Improves Botmill Quality   (Pages: 1 2) by 3DSbotmill	3,803	53	01/27/2012 08:56PM Last Post by spacexula
	ABS vs PLA by Bob hewson	2,134	7	01/27/2012 06:06PM Last Post by Skypuppet
	Help The New Guy by Drogon	822	5	01/27/2012 05:16PM Last Post by misan
	Printing a shim to level your bed? by hexitex	1,139	8	01/27/2012 12:42PM Last Post by geoffd
	Polyvinyl Alcohol for Support Material by Adam.m.Nelson	1,524	10	01/27/2012 07:12AM Last Post by richrap
	Most common software setup by shadowjig	1,236	11	01/26/2012 08:56PM Last Post by jkomp316
	powder plastic? by myearwood	867	2	01/26/2012 05:46PM Last Post by VDX
	Scaling Mendel by artemen	1,160	13	01/26/2012 10:54AM Last Post by Buback
	heated bed using diodes as heat sensors by jamesdanielv	1,102	4	01/26/2012 10:26AM Last Post by nophead
	Hobbed Bolt by JRMN	1,324	4	01/25/2012 07:25PM Last Post by NelsonRap
	Mendel drive belt options by RepRapRaggy	721	1	01/25/2012 09:45AM Last Post by RepRapRaggy
	best colour pla to setup my frist printer by dave86	1,728	9	01/25/2012 05:59AM Last Post by dave86
	Got Lucky! by zomie	970	2	01/25/2012 12:39AM Last Post by C. Cecil
	Please help, which printer to build..... by Adman234	1,365	19	01/24/2012 09:29PM Last Post by Adman234
	Commercial 3D printers now available for everyone? by canam	1,818	13	01/24/2012 05:59PM Last Post by sxt173
	Liner Cooked? J Head IV by zomie	999	4	01/24/2012 09:33AM Last Post by yydoctt
	ramps by glrra19	868	3	01/24/2012 04:18AM Last Post by glrra19
	Using RepRap to help the blind by rhertig	1,411	15	01/24/2012 03:05AM Last Post by johnrpm
	Advance 3D printer from Chinese supplier by Anonymous User	1,231	2	01/23/2012 04:24PM Last Post by construction2012
	End stops by NelsonRap	1,144	15	01/23/2012 01:34PM Last Post by jcabrer