Subject		Views	Posts	Last Post
	Any RepRapers from Melbourne Australia by 3eality	626	1	10/13/2012 01:21AM Last Post by 3eality
	Not another 3D printer company?!?!   (Pages: 1 2 3 4) by Chelsea - QU-BD	14,259	113	10/12/2012 11:23PM Last Post by Dad911
	Stepper Motor Voltage + Multimeter by hibijibi	1,250	3	10/11/2012 05:15PM Last Post by MattMoses
	Arduino Dead but Ramps Alive? by hibijibi	3,342	9	10/11/2012 03:54PM Last Post by hibijibi
	Help! Controlling a huge 3D printer by gtg252b	971	17	10/11/2012 12:32PM Last Post by gtg252b
	Bed Temp OK, but Heater Temp at 278C?... by ahbtsang	1,361	19	10/11/2012 11:30AM Last Post by norzam
	Which is the best open source 3D Printer to try? by simonstallone	905	5	10/11/2012 07:27AM Last Post by simonstallone
	Problem during printing PLA by Anais25	518	1	10/11/2012 06:41AM Last Post by Anais25
	Why wont stl files load? by virgodave61	488	2	10/11/2012 03:10AM Last Post by virgodave61
	Your Business/Product born from RepRap? by Deputy659	781	8	10/11/2012 12:00AM Last Post by Deputy659
	My thoughts and account of this years Maker Faire 2012 NYC by Simba	1,100	2	10/10/2012 10:59PM Last Post by keithCl
	The next generation of the Reprap concept by jzatopa	1,381	13	10/10/2012 10:15PM Last Post by Wired1
	Community Driven 3D Model Upload Site? by moli	979	10	10/10/2012 09:08PM Last Post by jzatopa
	How Has MakerBot Supported You? Tell Your Story   (Pages: 1 2) by Idolcrasher	2,625	36	10/10/2012 07:18PM Last Post by jzatopa
	Heated bed (AC) on Ramps, support needed. by Core	1,061	3	10/10/2012 04:32PM Last Post by Core
	Who wanna win a free roll of fabberdashery filament ? by DeuxVis	732	1	10/10/2012 03:55AM Last Post by DeuxVis
	Webcam anyone? by Wired1	641	3	10/10/2012 03:11AM Last Post by Wired1
	Worth paying extra for 'premium' ABS ? by mmt	978	6	10/10/2012 01:36AM Last Post by jamesdanielv
	Slic3r base very thin by epareja	688	4	10/10/2012 01:26AM Last Post by jamesdanielv
	Smaller is Beautiful by Just_Colin	887	7	10/09/2012 10:26PM Last Post by eyenoseyou
	Gen 6.d getting USB device not recognized (error 43) by Corruo	752	4	10/09/2012 10:25PM Last Post by eyenoseyou
	New 3D Printer Design: Arm-based, able to make electronics full auto by daveycrocket	4,218	24	10/09/2012 10:48AM Last Post by ttsalo
	Safety cutoff started to burn by Anais25	542	3	10/09/2012 06:57AM Last Post by orcinus
	The 3D printer of the future has 6 primary materials by Simba	1,340	1	10/09/2012 12:47AM Last Post by Simba
	Melted power terminal by IanJohnson	1,004	9	10/08/2012 10:09PM Last Post by brnrd
	Constructive discussion about replicator controversy by Jasper1984	1,135	13	10/08/2012 09:08PM Last Post by pricecw
	Stuck in Solidworks and need help.   (Pages: 1 2) by Dark Alchemist	3,812	60	10/08/2012 08:05PM Last Post by Dark Alchemist
	Kit vs. buyning components by sungod3k	1,204	11	10/08/2012 07:27PM Last Post by Wired1
	Decent tap and die set (metric) under £40 in UK? by Ollie	2,848	6	10/08/2012 01:13PM Last Post by mmt
	bent stepper motor shaft by nic0laz	3,369	15	10/08/2012 10:56AM Last Post by jamesdanielv