Welcome! Log In Create A New Profile

Advanced

General

General discussions. For specific printers / electronics / fabrication methods / softwares, please see other sections. 
Subject Views Posts Last Post

Command line gcode sender for linux supporting Marlin

by mmiscool
133 3 07/31/2017 04:34AM
Last Post by Dust

Futuristic FDM idea!

by clearlynotstefan
274 8 07/30/2017 01:27PM
Last Post by andornot

Simplify3D retraction before first layer

by mersadk
303 8 07/30/2017 10:11AM
Last Post by Floyd

DIY LCD Resin printer

by harlandraka
186 3 07/30/2017 01:43AM
Last Post by harlandraka

Looking for others to road test new extrusion system

by Arnold Lane 1000
429 11 07/29/2017 03:01AM
Last Post by Srek

MKS gen1.4 compatibility and changes.

by chromaglow
202 4 07/28/2017 10:45PM
Last Post by jinx

rambo v1.3 atx help needed

by stefi01
111 2 07/27/2017 10:46PM
Last Post by Dust

i3 prusa hephestos (CURA print one at a time)

by scrumpy0jack
892 13 07/27/2017 04:00PM
Last Post by guysoft

TMC 2100 and ramps - any pitfalls to avoid? Attachments   (Pages: 1 2 3 4)

by DjDemonD
3,814 91 07/27/2017 01:29AM
Last Post by dc42

Help me to buy a new printer - please

by Bking1340
192 1 07/26/2017 04:45PM
Last Post by Bking1340

Z probe questions

by leadinglights
596 17 07/26/2017 07:38AM
Last Post by DjDemonD

Extrusion multiplier not working. Attachments

by MeepleMorph
231 3 07/26/2017 04:09AM
Last Post by the_digital_dentist

AUTOBED_only one point Attachments

by tekos21
186 1 07/25/2017 04:07PM
Last Post by tekos21

Enclosure

by ntar827
321 8 07/25/2017 12:26PM
Last Post by the_digital_dentist

S3D 4.0 arrives this month

by Origamib
469 8 07/25/2017 07:42AM
Last Post by Origamib

SD card/ Full graphic display puzzle

by Ed would
339 5 07/25/2017 01:07AM
Last Post by Dancer

Where to find Vase Mode?

by stan510
222 6 07/24/2017 03:30PM
Last Post by scottybfg

Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN question Attachments

by Dr Bob
170 5 07/24/2017 05:48AM
Last Post by Dr Bob

Best Dust Collection System for Fab Lab?

by thinktankgroup
224 3 07/24/2017 05:27AM
Last Post by thinktankgroup

Filament diameter compensation Attachments

by RGN01
473 17 07/23/2017 06:43PM
Last Post by kengineer

Conductive build plate?

by DjDemonD
508 22 07/23/2017 06:29PM
Last Post by prot0typ1cal

Opportunity to publish open source inventions in 3D printing

by Jpearce
213 1 07/23/2017 04:00AM
Last Post by Jpearce

Remote Direct Drive effectors for E3D Chimera / Cyclops (Zesty Nimble et al) Attachments   (Pages: 1 2 3 4)

by RGN01
3,287 96 07/22/2017 11:03PM
Last Post by Lykle

From 12V to 24V

by Dr Bob
349 15 07/22/2017 10:53PM
Last Post by o_lampe

RepRapish DLP Resin 3D Printer

by fswallride
412 9 07/22/2017 01:04AM
Last Post by VDX

Need help with new board

by theblindsaint
782 23 07/20/2017 11:35PM
Last Post by theblindsaint

Survey about 3D printing

by teragolem
259 6 07/20/2017 12:11PM
Last Post by teragolem

Need serious help connecting printer to computer

by tatelewis
440 20 07/20/2017 08:53AM
Last Post by Wired_Bob

Hephestos 2 (Using Vanilla Marlin / Heatbed Issues) Attachments

by stonecoldfx
254 2 07/20/2017 05:30AM
Last Post by stonecoldfx

Calibration Offset

by Bony
188 5 07/20/2017 05:01AM
Last Post by MCcarman