Subject		Views	Posts	Last Post
	just posted arudino code that simplifies bt setup by jamesdanielv	518	1	09/19/2013 07:44AM Last Post by jamesdanielv
	z-motors (Prusa) not move on Gen6. by guille	534	4	09/19/2013 05:59AM Last Post by rhmorrison
	Hybrid tooling (3D printing + milling) patented ?! by RepRaper007	578	3	09/19/2013 03:07AM Last Post by johnrpm
	[UK] MendelMax 2 Laser cut parts needed. by hdp160	1,143	8	09/18/2013 07:08PM Last Post by NormandC
	help me figuring out what to change by victorjung	432	11	09/18/2013 02:21PM Last Post by victorjung
	Questions of building a 3D printer by hujdffjdfd	597	3	09/18/2013 02:20PM Last Post by jorisrf
	Cubehero discussion sections now available for all project physibles by iamwil	327	1	09/18/2013 01:21PM Last Post by iamwil
	Cold 3D printing [solved?] by gmerz	743	6	09/18/2013 01:12PM Last Post by Robin2
	How can I increase my print speed? by willer2k	1,616	11	09/18/2013 11:08AM Last Post by cope413
	Extruder drive gear slop :-( by cobrageek	835	4	09/18/2013 10:05AM Last Post by cobrageek
	Do you doubt a 3D printer could dance? by 3Dmaker4U	776	4	09/18/2013 09:23AM Last Post by 3Dmaker4U
	Adding WiFi support to Marlin with RAMP1.4   (Pages: 1 2) by pfinucan	12,131	36	09/18/2013 07:45AM Last Post by marj03
	Ali-express MK7 stepstruder by chris...	1,002	1	09/17/2013 05:08PM Last Post by chris...
	University project: Market analysis for Open Source, 3d printable car by Proot	850	10	09/17/2013 03:52PM Last Post by Robin2
	Electronics and software combination questions   (Pages: 1 2 3) by jmaeding	2,297	72	09/17/2013 01:37PM Last Post by Robin2
	Thermocouple usage by Meirbns	3,934	4	09/17/2013 12:27PM Last Post by iLyngklip
	Teaching kids how to build and use tech by thetechelective	389	1	09/17/2013 10:59AM Last Post by thetechelective
	DIY Tech or MakerFarm by eleeptg	538	1	09/17/2013 09:36AM Last Post by eleeptg
	Common Wisdom - Print ABS hot to stick first layer ? Try cooler! by pocketmoon	549	3	09/17/2013 05:40AM Last Post by pocketmoon
	So I want to upgrade my hot end but I have questions by NjEmt527	1,164	7	09/17/2013 12:26AM Last Post by nechaus
	What section wire to use for the hot end resistor? by WestMD	1,965	17	09/16/2013 10:22PM Last Post by cozmicray
	From Fab@Home to Repstrap... but with a tracking issue. by InnovativePrinting	633	10	09/16/2013 01:06PM Last Post by LoboCNC
	pulling my hair out over slic3r .9.10 support material by charlieRC	913	9	09/16/2013 08:19AM Last Post by rhartman80
	FDM 2000 Print Head by erkan	618	1	09/16/2013 02:55AM Last Post by erkan
	Getting ramps1.4 recognised on arduino IDE by Rui.in.Roskill	500	5	09/15/2013 11:15PM Last Post by Rui.in.Roskill
	Recommended Hot End and Extruder for Prusa I3? by jininjin	554	1	09/15/2013 10:14PM Last Post by jininjin
	mendel max 2.0 laser cut parts by pr77	1,017	5	09/15/2013 10:01AM Last Post by hdp160
	First time connecting 3D printer. Problems with Y and Z end stop. by WestMD	1,268	2	09/15/2013 09:34AM Last Post by WestMD
	Reusing Contraptions - Looking for Inspiration by Isos	511	3	09/15/2013 06:38AM Last Post by f3rDz
	Why does firmware use acceleration? by Robin2	907	19	09/15/2013 05:01AM Last Post by bobc