Subject		Views	Posts	Last Post
	Printing nylon--new Garolite LE (McMaster 8474K141) very warped! by calinb	9,011	13	10/11/2013 01:41AM Last Post by calinb
	High temperature stepper motor? by DingbatCA	4,229	20	10/10/2013 10:48PM Last Post by aduy
	What to do with my Rapman 3.1??? by gmh39	1,668	7	10/10/2013 10:35PM Last Post by gmh39
	connecting fan to gen7 electronics by dave584	1,746	6	10/10/2013 07:46PM Last Post by Traumflug
	Have a mechanical drawing for Kossel or Rostock end effector? by Joseph	825	3	10/10/2013 06:18PM Last Post by Joseph
	source(s) for bowden (PTFE, Teflon, other?) tubing in the US? by discocyborg	8,575	14	10/10/2013 05:58PM Last Post by REPRAP SQUAD
	Will a A6 HT Acrylic with heat bed from Makibox make a RepRap? by ArcherMalone	782	2	10/10/2013 01:20PM Last Post by cozmicray
	Hurray! the low cost 3D printed robot prosthetic hand just met it's target on Indiegogo by Senake	1,002	4	10/09/2013 11:25PM Last Post by NormandC
	Filament prices rising?!?   (Pages: 1 2 3) by tleneel	3,016	61	10/09/2013 08:18PM Last Post by greenman100
	Hotend fan by Rigor_M	2,016	7	10/09/2013 06:53PM Last Post by psilocin
	Calibration is driving me absolutely nuts, simple question. (Pics) by SamS	688	5	10/09/2013 10:46AM Last Post by rhartman80
	Ever wanted to shoot vodka into your mouth? by iamwil	1,172	8	10/09/2013 05:20AM Last Post by DeuxVis
	Any way to reprint a layer due to filament jam? by Lance448	1,293	7	10/08/2013 03:42PM Last Post by paucus
	Print square wall but output rectangle wall by James4D	1,458	7	10/08/2013 12:27PM Last Post by RP Iron Man
	Wax filament for FDM 3D printers? by bardiaesm	2,604	5	10/08/2013 10:28AM Last Post by TCase
	You pay Staples $100 a month to sell your designs by A2	753	2	10/08/2013 06:39AM Last Post by A2
	3.06V, 1.7A stepping motors on ramps 1.4? by bardiaesm	683	2	10/08/2013 01:09AM Last Post by jamesdanielv
	The Trimmer line thread by nechaus	1,624	8	10/08/2013 12:30AM Last Post by aduy
	Bed Heater by cfellows	549	4	10/07/2013 10:41PM Last Post by nechaus
	unipolar or bipolar stepper motor for ramps 1.4 with A4988 driver? by bardiaesm	3,111	4	10/07/2013 08:32PM Last Post by bardiaesm
	How to apply kapton tape to glass plate? by Jo1212	4,071	17	10/07/2013 05:10PM Last Post by aduy
	Need help with the electronics and Hot end by Jeehroen	832	4	10/06/2013 05:47PM Last Post by jaydmdigital
	Cheapest Electronics by Jeehroen	1,100	12	10/06/2013 05:18PM Last Post by pokey9000
	Kossel build instructions? by Joseph	1,037	3	10/06/2013 04:37PM Last Post by Joseph
	Choosing the correct (4) Nema 17 motor(s) for MM2 by hdp160	1,483	3	10/06/2013 02:05PM Last Post by hdp160
	Z step rate issue by psilocin	973	4	10/05/2013 08:30PM Last Post by psilocin
	Make internal threads... by imzack	3,106	8	10/05/2013 06:17PM Last Post by NormandC
	What are the advantages and disadvantages? by ikaarus	1,099	2	10/05/2013 05:12PM Last Post by tom10122
	initial configuration trouble? by sage19175	876	8	10/05/2013 01:16PM Last Post by sage19175
	Repetier-host finishes job before print completed by dwonh	1,054	3	10/05/2013 11:15AM Last Post by dwonh