Subject		Views	Posts	Last Post
	MAGMA hotend ANTI-CLOGGING solution by jaak lab	1,529	23	01/15/2014 10:15PM Last Post by nechaus
	Do you have problems with PVA? by tleneel	473	1	01/15/2014 09:29PM Last Post by tleneel
	[PRUSA I3]: Direct extruder by aj.moreno	1,511	6	01/15/2014 09:19PM Last Post by brnrd
	Taulman T-Glase by drawcut	2,591	29	01/15/2014 08:19PM Last Post by Antslake
	rostock max / repetier resetting itself by UMFprinter	669	2	01/15/2014 08:06PM Last Post by jamesdanielv
	Calibration by mondo50m	751	5	01/15/2014 07:29PM Last Post by Juan
	Filament diameter - differences between 1.75mm and 3.0mm   (Pages: 1 2) by netsrac	7,847	49	01/15/2014 04:45PM Last Post by aduy
	Rostock or Prusa i3 by KD0SKH	1,479	4	01/14/2014 06:39PM Last Post by Ohmarinus
	Layer Adhesion Problems with ABS-PC and Polycarbonate   (Pages: 1 2) by uGen	9,635	44	01/14/2014 02:38PM Last Post by aduy
	Looking for good Repetier settings for Printrbot? by naomirobosavvy	1,010	1	01/14/2014 08:14AM Last Post by naomirobosavvy
	K Extruders by john230873	983	8	01/14/2014 02:07AM Last Post by lazzymonk
	mendelmax calibration by cuacharpas	891	6	01/13/2014 11:35PM Last Post by jamesdanielv
	Frame materials by roontoon	477	4	01/13/2014 07:54PM Last Post by cnc dick
	What's better on z-axis? Belts or leadscrews? by jpan	7,164	21	01/13/2014 06:40PM Last Post by jpan
	Can you recommend a printer by Bliss	447	3	01/13/2014 06:00PM Last Post by jebba
	Move head after print is done? by Hobbes20xx	1,148	8	01/13/2014 09:30AM Last Post by Dirty Steve
	Noob - help with generating Mendel90 BOM by Jerms.a320	482	2	01/13/2014 02:41AM Last Post by Jerms.a320
	First layer has 'wispy bits' by ayouden	498	4	01/13/2014 02:17AM Last Post by Srek
	Need help with ninja flex by Antslake	4,362	8	01/12/2014 11:00PM Last Post by aduy
	Help with first Printer Hot End by luillo1	447	2	01/12/2014 05:49PM Last Post by Ohmarinus
	who decides to close a thread by jinx	671	11	01/12/2014 07:09AM Last Post by bobc
	when quality control fails by jinx	924	7	01/12/2014 05:04AM Last Post by cevinius
	Ultimate Guide to 3D Printing 2014? by onion_pepper1	657	2	01/11/2014 05:42PM Last Post by cat.farmer
	heat shrink tubing for nema17 wire? by augus	870	6	01/11/2014 05:40PM Last Post by anode505
	Dissolving PLA without harm to cured Polyurethane/Silicone by cferraz	2,210	11	01/11/2014 05:30PM Last Post by A2
	Arduino creator explains why open source matters in hardware, too by bobc	1,125	13	01/11/2014 04:41PM Last Post by Nil Einne
	Slic3r Being very strange! by ayouden	629	7	01/11/2014 04:04PM Last Post by Ohmarinus
	Advise to get faster Prints ? by Foxen	731	3	01/11/2014 03:23PM Last Post by brnrd
	Any reviews on this? by Dark Alchemist	1,693	16	01/11/2014 12:19PM Last Post by brnrd
	Cupcake CNC 3G 5D or Ugly Cable Hack help Please by umdpru	2,243	16	01/11/2014 10:42AM Last Post by umdpru